User manual BEHRINGER DJX400

[. . . ] DJX400 Users Manual Version 1. 0 August 2002 PRO MIXER www. behringer. com ENGLISH PRO MIXER DJX400 SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: All the safety and operation instructions should be read before the device is operated. Retain Instructions: The safety and operating instructions should be retained for future reference. Heed Warnings: All warnings on the device and in the operating instructions should be adhered to. Follow instructions: All operation and user instructions should be followed. [. . . ] A special feature allows you to switch the input sensitivity of the phono input to line-level, giving the phono connector flexibility (see ). 2. CONTROL ELEMENTS 5 PRO MIXER DJX400 happen, the MASTER signal is the only one that would be heard. The MASTER signal is taken post MASTER LEVEL control, whereas the signals from the two input channels are pre CHANNEL faders and are routed to the MONITOR section. MONITOR SELECT Headphones output CH-1 CH-2 MASTER L R ON OFF OFF CH-1 "L" CH-1 "R" OFF ON OFF CH-2 "L" CH-2 "R" OFF OFF ON MASTER "L" MASTER "R" ON ON OFF CH-1 "L" + CH-2 "L" CH-1 "R" + CH-2 "R" ON OFF ON CH-1 "MONO" MASTER "MONO" OFF ON ON CH-2 "MONO" MASTER "MONO" 2. 6 Front panel connectors Table 2. 1: Selecting a signal with the Monitor Select button 2. 4 MASTER section The LEVEL METER displays the signal level selected with . With this switch you determine whether it is the MASTER or the MONITOR signal to be indicated on the LEVEL METER. When the MONITOR LED lights up, it indicates the level of the headphones signal. Fig. Each channels DISPLAY indicates the track tempo. Several tempo changes in one track would produce a constant display of various BPM values and thus lead to unnecessary confusion. Thats why the beat counter sections each have a SYNC LOCK button that can be used during the song to limit the range of possible tempo values. This makes sense if the counter has already calculated a realistic value. Pushing this button manually with the BEAT ASSIST button at least three times in sync with the songs tempo results in the calculated tempo appearing in the DISPLAY. The BEAT ASSIST and SYNC LOCK buttons are each equipped with a LED. When you have limited the tempo of the tracks on both channels with the SYNC LOCK or BEAT ASSIST buttons, the difference in tempo from channel 1 and channel 2 is illustrated in the form of a nine-character message on the TEMPO DIFFERENCE-LED . The extent of the difference in tempo is indicated by a corresponding swing to the right (the channel 1 signal is slower) or to the left (the channel 2 signal is slower). When the middle LED lights up, the tempi are the same. The TIME OFFSET LED below that displays the channel 1 and 2 synchronisation. Should the middle LED light up, the tracks are synchronised. Should the display move to the left or right, either channel 1 or channel 2 is not synchronised. The TEMPO DIFFERENCE and TIME OFFSET displays are only active if the tempi of both channels have been fixed in one of the ways described. 6 2. CONTROL ELEMENTS PRO MIXER DJX400 To exit the SYNC LOCK or BEAT ASSIST modes, simply push the SYNC LOCK button once more on both channels. To be sure, slide all the faders to the bottom and switch all controls to the zero position. Using the TAPE output you can record your music by connecting devices such as tape decks, DAT recorders etc. Unlike the MASTER output, the output volume is fixed, making it necessary for you to adjust the input level on the recording device. [. . . ] This also applies to defects caused by normal wear and tear, in particular, of faders, potentiometers, keys/buttons and similar parts. Damages/defects caused by the following conditions are not covered by this warranty: s improper handling, neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals. s connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used. s damages/defects caused by force majeure or any other condition that is beyond the control of BEHRINGER. [. . . ]