User manual BEHRINGER DSP1100P

[. . . ] PRO DSP1100P User´s Manual Bedienungsanleitung Version 1. 0 October 1998 E D FEEDBACK DESTROYER ® www. behringer. de 1 EG-Declaration of Conformity Spezielle Studiotechnik GmbH acc. to the Directives 89/336/EWG and 73/23/EWG We, BEHRINGER INTERNATIONAL GmbH Hanns-Martin-Schleyer-Straße 4 D - 47877 Willich Name and address of the manufacturer or the introducer of the product on the market who is established in the EC herewith take the sole responsibility to confirm that the product: FEEDBACK DESTROYER PRO DSP1100P Type designation and, if applicable, Article-No which refers to this declaration, is in accordance with the following standards or standardized documents: x EN 60065 x EN 55020 x EN 55013 x EN 61000-3-2 x EN 61000-3-3 x EN 55022 The following operation conditions and installation arrangements have to be presumed: acc. Nier, President Name, address, date and legally binding signature of the person responsible Willich, 01. 10. 1998 2 SAFETY INSTRUCTIONS CAUTION: To reduce the risk of electrical shock, do not remove the cover (or back). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. [. . . ] On its right-hand side, the display reads a capital C (=Controller). The jog wheel selects one of the following four controller modes: Displa y 0 1 2 3 4 Mode No controller data are transmitted Controller data are received but not transmitted Controller data are transmitted but not received Controller data are transmitted and received As 3, with additionally the automatic filter parameters Tab. 2. 2: Controller settings + When you choose value 4 the FEEDBACK DESTROYER PRO will also send the settings of the automatic filters. The fourth page gives you access to the program change setup. The display reads a capital P (=Program). Here, too, four modes can be selected with the jog wheel, as follows: Display 0 1 2 3 Mode No program change data are transmitted Program change data are received but not transmitted Program change data are transmitted but not received Program change data are transmitted and received Tab. 2. 3: Program change settings The fifth page of the MIDI menu shows the store enable flag represented by a capital S in the display. The value 0 disables the reception of controller #18, and therefore protects the user presets from being modified 14 2. Accordingly, the value 1 enables MIDI controller #18 so that you can modify or replace presets with a remote MIDI device or a sequencer. In this case the actual settings will be stored directly to the location that corresponds to the controller value. + Attention!Since the store enable mode allows you to access memory locations directly via MIDI, it is possible that stored presets will be replaced or altered if controller #18 messages are sent on the same MIDI channel. The purpose of this mode is to facilitate MIDI backup and restore operations without express confirmation at the FEEDBACK DESTROYER PRO. It is therefore recommended to disable (flag=0) this mode as soon as the intended data transfer has ended. This is done automatically when you switch off the FEEDBACK DESTROYER PRO. On the sixth, and presently the last, page you can access the System Exclusive functions. This is indicated by a d (for dump) in the display. To the left of this d a number is displayed: - 0 means that no SYSEX data will be sent or accepted. - 1 will enable the FEEDBACK DESTROYER PRO to receive data. When STORE is pressed the unit will wait for data, this is shown by flashing dots (LEDs) in the display. The MIDI button LED flashes signaling that SYSEX data is being received. - 2 will enable the FEEDBACK DESTROYER PRO to send a bulk dump. Start your sequencer and press STORE on the unit to start the transmission. If you press the IN/OUT key again on the fifth page, the FEEDBACK DESTROYER PRO quits MIDI setup mode. To load these settings again, select 1, press STORE and start your sequencer. [. . . ] Damages/defects caused by the following conditions are not covered by this warranty: s misuse, neglect or failure to operate the unit in compliance with the instructions given in the user or service manuals. s connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used. s damages/defects that are caused by force majeure or by any other condition beyond the control of BEHRINGER INTERNATIONAL. Any repair carried out by unauthorized personnel will void the warranty. [. . . ]