User manual BEHRINGER XENYX 1622FX

[. . . ] 1622FX 1832FX 2222FX 2442FX Users Manual Version 1. 0 January 2006 XENYX XENYX 1622FX/1832FX/2222FX/2442FX IMPORTANT SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: 1) Read these instructions. CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. 5) Do not use this apparatus near water. [. . . ] An example follows (1622FX wired to an effects device): Monitor mix with effect In this instance, your effects device should be set up as follows: the AUX SEND 2 jack should be connected to the L/Mono input of your effects device, with its outputs coming back into the STEREO AUX RETURN 1 jacks. Fig. 2. 10: Monitor output of the 1832FX The first aux send (MON) on this console is used to set up the monitor mix from the channels and route it to the MON SEND fader. Connect the AUX SEND 1 jack output to the amplifier of your monitor system. The AUX SEND 1 master control determines the overall volume of the monitor mix. Using the STEREO AUX RETURN (TO AUX SEND) control, the effect signal can now be blended into the monitor mix. You can easily use the headphones distribution amplifier BEHRINGER POWERPLAY PRO HA4700/HA8000 to provide four (HA8000: eight) stereo headphone mixes for your studio. The following table shows which jacks on the console can be used for this purpose. @rhyrssrp qrvprrprvr vthys AUX SEND ! @rhyrssrp Uurrssrpvthy qrvprrvthy rhpururv ihpx vvh %!!AY STEREO AUX RETURN connectors STEREO AUX RETURN (TO AUX SEND ) control '"!AY AUX SEND STEREO AUX RETURN !connectors MONITOR switch of the FX/AUX!2. 11: Monitor fader of the 1832FX MUTE Press the MUTE switch to mute the monitor send. SOLO The SOLO switch routes the monitor send to the solo bus (post-fader and post-mute) or to the PFL bus (pre-fader and pre-mute). The position of the MODE switch in the main section determines which of the buses is selected. AUX SEND!STEREO AUX STEREO AUX RETURN connectors RETURN (TO AUX !STEREO AUX RETURN connectors STEREO AUX RETURN (TO AUX SEND ) control STEREO AUX RETURN !(TO AUX SEND !) control vhy) 2. 3. 5 Stereo aux return control STEREO AUX RETURN 1 The STEREO AUX RETURN 1 control determines the level of this signal in the main mix. If STEREO AUX RETURN 1 is used as effects return, this will determine the level of the effects when mixed with any dry channel signal. AUX SEND STEREO AUX RETURN !2. 1: Connectors and controls for monitor mix with effect STEREO AUX RETURN FX On consoles 1622FX and 1832FX this is the STEREO AUX RETURN 2, on consoles 2222FX and 2442FX this is the STEREO AUX RETURN 3. + When used in this way, the effects device should be set at 100% effect. 2. CONTROL ELEMENTS AND CONNECTORS 9 XENYX 1622FX/1832FX/2222FX/2442FX Use the STEREO AUX RETURN FX control to determine the level of the signal routed from the AUX RETURN FX jacks to the main mix. If nothing is connected to these jacks, the output of the built-in effects module will appear. MAIN MIX / TO SUBS This switch routes the signal fed in via the STEREO AUX RETURN FX jacks either to the main mix (not pressed) or to the submix (pressed). On the 2442FX you can select which subgroup the signal is assigned to (switches 1-2 / 3-4, to the right of MAIN MIX / TO SUBS). SOLO RETURNS Additionally, this model allows you to route the aux returns together to the solo bus and the PFL bus. STEREO AUX RETURN 4 (2442FX only) This control behaves the same way as the other stereo aux returns. Additionally, it provides for a simple monitor path using the switch PHONES/CTRL ROOM ONLY. [. . . ] connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used. damages/defects caused by force majeure or any other condition that is beyond the control of BEHRINGER. s s 5. Any repair or opening of the unit carried out by unauthorized personnel (user included) will void the warranty. If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty, the inspection costs are payable by the customer. [. . . ]