User manual BELINEA 101915

[. . . ] [ USER MANUAL LCD-Monitor Belinea 10 19 15 ] BELINEA PREMIUM SERVICE English The three-year return to base warranty for your Belinea monitor includes all parts and labour. In addition many countries offer a free of charge swap out warranty programme. This does not affect your Statutory Rights. Please visit http://www. belinea. com or call the numbers below for further warranty or service information. [. . . ] Use only warm water and then wipe the monitor dry. Solvents or harsh cleaners can damage the housing. Clean the display surface only with a soft cloth, otherwise you may damage the display's coating. If the monitor is only slightly dirty, clean it using a soft, dry and antistatic cloth. The LCD monitor's screen surface is very sensitive. Please avoid any contact with the surface (finger, pencil etc. ) and be especially cautious during transportation since jolts and shocks can cause the screen to become scratched (always use the original packaging). WALL MOUNTING The Belinea monitor is shipped with the standard desktop configuration. However, you can optionally mount the device on a wall or on a monitor swivel arm (optional accessory). Please follow the corresponding instructions (4-hole assembly with a spacing of 100 100 mm according to the international VESA FDMI standard). Belinea 10 19 15 - Operating Instructions - 3 ENGLISH UNPACKING Carefully lift the monitor out of the packaging and make sure that all components are included (see fig. Save the original box and packing material in case you have to ship or transport the monitor. To set up the device, you must fit the monitor base together. When the base of the monitor is extended, you can tilt the monitor 90 (Pivot function). Audio cable Power cord VGA cable DVI-D cable (optional) Figure 1. Monitor with swivel base CONNECTING To connect the monitor to your PC . . . . . . . . . . . . . . . . . . . . . . . . Make sure that the PC and monitor are unplugged. Connect the 15-pin signal cable to the PC (see fig. If you have a graphic card with a digital DVI-D connector (24-pin socket), then connect one end of the DVI-D cable (optional) to the DVI-D connector of your monitor (see fig. 2b), the other end to the computer. D-SUB AUDIO IN Figure 2b. Connection via the DVI-D interface D-SUB AUDIO IN Signal cable D-SUB AUDIO IN 2 1 Figure 2a. Connecting the monitor to the PC To connect the monitor to the power source . . . . . . . . Connect the separate power cable ( monitor and a grounded outlet. 3) to the Connecting the audio cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . If your computer is equipped with an audio output port, then connect one end of the sound cable to the audio input connector of the monitor ( in fig. 3) and the other end to the Line-Out connector of the computer. Figure 3. [. . . ] Loss of customer-specific data or software from repair and installation processes Improper use of machine capacity or output Inappropriate customer operating environment The MAXDATA warranty also does not cover the following: MAXDATA products from which the category plates, serial numbers, part numbers on the machine of machine parts have been removed or changed Decline in rechargeable battery capacity after the end of the 6 month warranty period The provision and installation of BIOS, driver or software updates/upgrades The new installation of software/operating systems that are no longer able to run (e. g. because of the deletion of system-relevant files, incorrect system settings or self-copying programs, e. g. computer viruses) Wear and tear on data storage media, LCD background lighting, CRTs on CRT monitors, picture tube burn-in or loss of brightness MAXDATA products for which the warranty seal has been broken by entities other than MAXDATA or those authorised by MAXDATA Breaks and scratches on TFT panels and CRT displays Damage through use of force and external impact respectively Spots on the panel caused by external impacts Belinea 10 19 15 - Operating Instructions - 8 ENGLISH Colour spots resulting from falls Error class 2 pixel errors (please note the information on ISO 13406-2 on the website of the MAXDATA subsidiary concerned) If the device received by MAXDATA demonstrates two defects and only one of these is covered by the MAXDATA warranty claim, the customer only has the right to repair for the damage to his device covered by the warranty. In this case MAXDATA reserves the right to offer the customer several options on resolution in the form of a quotation and to charge the relevant processing costs. [. . . ]