User manual BELKIN F1D001

[. . . ] User Manual ePowerSwitch By: BELKIN 34000179 19-Sep-02 Copyright© 2000 Trademarks IBM, IBM NetView/6000 are trademarks or registered trademarks of International Business Machines Corp. Hewlett-Packard, HP, HP Open View are trademarks or registered trademarks of Hewlett-Packard Company. Microsoft, MS, MS-DOS, XENIX are registered trademarks and Windows, Windows NT, LAN Manager, and Win32 are trademarks of Microsoft Corporation. NT is a trademark of Northern Telecom Limited. [. . . ] User may browse and control ePowerSwitch with this dynamic IP 4. Check the disconnection on the bottom of the PPP configuration page after work. 18 User Management Administrators can assign the maximum of 4 users to control the outlet. 19 20 Software Update This is the place you can upgrade the firmware when it is available or bug fix. 20 ePowerSwitch Configuration Each outlet can be individually programmed to enable ring On/Off or reset. Power resume delay is convenient for sequential startup. Name of each outlet can be labeled to whatever you like it to be called. For example, server1, DSL modem, webserver1, etc. Since 16 ePowerSwitches can be daisy chained together to share one NIC, so each unit can be individually named. The last item "Enable waiting device shutdown" is dedicated to Microsoft Windows NT (4 and 2000, workstation and server) to have a safe shutdown. If you installed an optional NT card inside the ePowerSwitch, there is a delay time for the corresponding outlet of the NT card to off the power for the safe shutdown functionality. The default delay time is set up as 5 minutes. 21 22 To enable this safe shutdown function, in both NT and WIN 2000, you need to have three setting for the UPS to configure it. Connect the communication port on the rear of ePowerSwitch to NT or WIN 2000 server with the PC Communication cable. Connect the corresponding outlet on the rear of ePowerSwitch to the NT or WIN 2000 server with the PC input power cord. Check the corresponding box of safe waiting device shutdown in ePowerSwitch configuration page to enable this function. 22 Scheduled shutdown Scheduled shutdown can be accomplished here. Be careful with which outlet you are working. 23 24 Verify The ePowerSwitch Operation 1. After you complete all configuration settings and connect the ePowerSwitch System to the network, check the LINK status. Power and Link lights should be on all the times. Issue a PING command from the NMS (Network Management Station). a) If you do not get a response, check the card 's network connection and IP address. Perform a "get" and a "set. " a) If the get or set commands fail, check the ePowerSwitch System access controls. The manager must have read permission to execute a get command successfully and read/write permission to execute a set command successfully. (See Configuring the NMS section for a detailed discussion. ) Your ePowerSwitch is now installed and completely functional. 24 Upgrade Firmware TFTP Upgrade With a Web browser, click on "Software upgrade", input TFTP server's IP address and go. Make sure that the firmware file (For example: ups. bin) is located in the default directory of the TFTP server. RS232 Serial Port Console Upgrade The following steps guide you in connecting the ePowerSwitch System through the serial port 1. Connect the RS232 port to a dumb terminal/PC with a null serial cable. Power on the NIC card of the ePowerSwitch; ? [. . . ] Network Management Station Dry Closure Input Dry Closure Output EtherNet Gateway IP IP Address MAC MIB NC NIC NMS 34 NO OID Personality Router RS-232 SNMP Sub-Agent TCP/IP TES TFTP Server UDP/IP UPS Normally Open--Refers to a contact switch that is normally open. Object Identifier--The variables defined in a MIB. The current device specific software uploaded to the ePowerSwitch System A computer that manages traffic between different network segments or different network topologies. The network media can be different, but the higher level protocols must be the same. [. . . ]