User manual BELKIN P74976UKAP41000EA3M

[. . . ] Home Cinema Power Protection with PureFilterTM Technology Power Console PF50 User Manual AP41000ea3M Table of Contents Page PureAV Power Console Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Power Console Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Examples of the most common video components are listed below: 1. Projector Note: You can connect any type of video component into any of the video filter sockets. You are not limited to the components listed above. PureAV Power Console 13 Hookup and Installation Step 7 Connect Audio Components to the Audio Filter The PureAV Power Console contains an isolated audio filter that is optimised to clean and condition the power to all of your audio components. The audio filter also isolates your audio components from connected digital, video, and high-current audio components. Attach PureAV power cable labels to each component's power cable before you plug the cable into the sockets on the Power Console. Connect the power cables of your audio components to any socket labeled under the "Audio Filter". Examples of the most common audio components are listed below: 1. Tape Player Receiver (Preamp) Turntables PureAV Power Console Note: You can connect any type of audio component into any of the audio filter sockets. You are not limited to the components listed above. 14 Hookup and Installation Step 8 Connect High-Current Audio Filter The HiCurrent socket is specifically designed to filter out AC line noise while delivering maximum current to power-hungry amplifiers and other high-current audio components. Note: This socket bank should be programmed for "Delay". This allows your high-current amplifiers to turn on last and turn off first, avoiding that annoying, and potentially damaging "thump" from getting to your speakers. Attach PureAV power cable labels to each component's power cable before you plug the cable into the HiCurrent socket on the Power Console. Connect your high-current device into the "HiCurrent Filter". Examples of the most common high-current components are listed below: 1. Electrostatic Speakers Note: You can connect any type of high-current audio component into any of the high-current sockets. You are not limited to the components listed above. PureAV Power Console 15 Hookup and Installation Step 9 Connect your Pay-Per-View/Phone Line Your PureAV Power Console comes equipped with Pay-Per-View/phoneline protection with a built-in splitter. These are standard BT RJ11 phone ports and are labeled "Phone". Connect one end of your telephone cable to the wall port to which you normally connect your phone line. Connect the other end of your telephone cable to the Power Console phone port labeled "IN". Connect one end of the PureAV phone cable (included) to the Power Console phone port labeled "OUT". Connect the other end of this cable to the Pay-Per-View phone port on your cable TV or satellite receiver. To connect a telephone ­ Connect one end of another phone cable to the other Power Console phone port labeled "OUT". [. . . ] All PureAV Power Consoles must be plugged directly into the power source and must not be "daisy-chained" together in serial fashion with other power strips, UPSes, other surge protectors or extension cables. Any such installation voids the warranties provided herein. The Belkin Connected Equipment Warranty does not protect against acts of God (other than lightning) such as flood or earthquake or against war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (i. e. brownouts or sags), non-authorised program, or system equipment modification or alteration. [. . . ]