Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BELL EXPRESS VU 4700. We hope that this BELL EXPRESS VU 4700 user guide will be useful to you.
Lastmanuals help download the user guide BELL EXPRESS VU 4700.
Detailed instructions for use are in the User's Guide.
[. . . ] Table of Contents
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Installation and Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Components of the Satellite Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 . [. . . ] Thread a length of coaxial cable through the dish as shown in diagram 2. Slip the weather boot(s) onto the LNBF cable(s). To do this, insert the end of the cable with the screw connector into the smaller end of the boot and work it through. When you are finished the boot should slide freely over the cable but hold snugly when slipped up over the the screw connector. This is a difficult and somewhat painstaking job. (If possible, place weather boot on cable before putting on ÒFÓ connector).
Page 1-26
Installation and Setup Assembling the 90cm Dish
3. Slide the weather boot up securely to cover the cable/LNBF connection at the base of the LNBF. Slip the LNBF onto the end of the arm, until contact is made with the LNBF bracket stops and put in screw through arm and LNBF. Route and fasten the cable in a neat, unobtrusive manner in such a way so it cannot be damaged by accident. Connect the opposite end of the cable to your receiver, to the connector marked ÒSatellite InÓ. See page 1-36 for instructions concerning safety grounding. The assembly and mounting of the 60 cm Dish is complete. Proceed to page 1-35 Installing the Receiver.
STEP 3. 3: ASSEMBLING THE 90 CM DISH
STEP 3. 3A: PRE-ASSEMBLE THE PARTS (90 CM DISH)
ItÕs best to pre-assemble the dish indoors, so that it is all ready to place on the mast outdoors, quickly and easily . . . especially if itÕs cold out.
DISH
The complete system consists of three main parts: the dish mount, the dish assembly, and the receiver. The mount consists of the foot (base plate) and a bent pipe called the mast. The dish assembly consists of the antenna, or dish, the dish support bracket, the (LNBF) low noise amplifier, and the LNBF support arm. The receiver is also fully assembled.
LNBF
LNBF ARM
MOUNT MAST
Pre-assemble the Dish as follows: 1. Assemble the dish as indicated in the instructions which are included in the antenna box.
Page 1-27
Installation Guide
2. Determine your specific vertical elevation from the Table (page 1-44) and adjust the angular tilt of the antenna so that the centre of the top bolt on the Mast Head Clamp lines up with your vertical elevation position on the Mast Head elevation gauge. In our diagram here, it is set for 50 degrees. Lightly tighten the two bolts located in the curved slots on the mast head. Your antenna assembly is now ready to be placed on the outdoor mount assembly.
VERTICAL ELEVATION GAUGE
10 20 30 40
50
60
70
80
90
10 20 30 40
50
60
70
The mount for attaching the dish to the dwelling is made of steel and, as a result, it is very magnetic. [. . . ] Preview the setups to determine the one that most closely matches your equipment, and then use that setup as the basis for your wiring installation. Your Bell ExpressVu receiver must be connected to a phone line at all times to order Bell ExpressVu PPV programs using the receiver.
Page 1-58
Installation and Setup Wiring Setup Diagrams
WIRING SETUP DIAGRAMS
These Installation Instructions provide only the basic wiring setup diagram below. For more wiring setup diagrams, see the User Guide that came with the Bell ExpressVu system. Note: The off-air television antenna shown in the following diagram is optional.
ORDERING YOUR PROGRAMMING
You need to have your services activated before you can start enjoying your desired programming. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BELL EXPRESS VU 4700
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BELL EXPRESS VU 4700 will begin.