User manual BENQ GW2760HM

[. . . ] This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS). Do not look straight at the projector lens during operation. The intense light beam may damage your eyes. [. . . ] Adjusting Brightness The higher the value, the brighter the image. And the lower the setting, the darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible. +30 +50 +70 Adjusting Contrast The higher the value, the greater the contrast. Use this to set the peak white level after you have previously adjusted the Brightness setting to suit your selected input and viewing environment. -30 0 +30 Adjusting Color Lower setting produces less saturated colors. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic. Adjusting Tint The higher the value, the more reddish the picture becomes. The lower the value, the more greenish the picture becomes. Adjusting Sharpness The higher the value, the sharper the picture becomes. The lower the value, the softer the picture becomes. Operation 29 Please refer to the illustration to the right for how the colors relate to each other. For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta. Press to highlight Saturation and adjust its values to your preference by pressing / . Every adjustment made will reflect to the image immediately. Magenta Cyan BLUE For example, if you select Red and set its value at 0, only the saturation of pure red will be affected. Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic. Press to highlight Gain and adjust its values to your preference by pressing . The contrast level of the primary color you select will be affected. [. . . ] 000 VGA_60* VGA_72 640 x 480 VGA_75 VGA_85 720 x 400 720 x 400_70 SVGA_60* SVGA_72 SVGA_75 800 x 600 SVGA_85 SVGA_120** (Reduce Blanking) XGA_60* XGA_70 XGA_75 1024 x 768 XGA_85 XGA_120** (Reduce Blanking) 1152 x 864 1152 x 864_75 BenQ 1024 x 576 Notebook_timing BenQ 1024 x 600 Notebook_timing 1280 x 720 1280 x 720_60* 1280 x 768 1280 x 768_60* WXGA_60* WXGA_75 1280 x 800 WXGA_85 WXGA_120** (Reduce Blanking) SXGA_60*** 1280 x 1024 SXGA_75 SXGA_85 1280 x 960_60*** 1280 x 960 1280 x 960_85 1360 x 768 1360 x 768_60*** 1440 x 900 WXGA+_60*** 1400 x 1050 SXGA+_60*** 1600 x 1200 UXGA*** 1680 x 1050 1680x1050_60*** 640 x 480@67Hz MAC13 832 x 624@75Hz MAC16 1024 x 768@75Hz MAC19 1152 x 870@75Hz MAC21 • *Supported timing for 3D signal with Frame Sequential, Top Bottom and Side by Side format. **Supported timing for 3D signal with Frame Sequential format. ***Supported timing for 3D signal with Top Bottom and Side by Side format. Specifications 57 • The timings showing above may not be supported due to EDID file and VGA graphic card limitations. [. . . ]