User manual BENQ P211 Document

[. . . ] i Copyright Copyright Copyright (c) 2002 by Benq Corporation. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Benq Corporation. Disclaimer Benq Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, Benq Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of Benq Corporation to notify any person of such revision or changes. ii Reference Fill in here!! For the convenience of service, write following related information of your monitor in the space below. The serial number is on the back of the product. Monitor Information Product Name: Serial Number: Date of Purchase: Dealer Information Dealer: Telephone: Number: Address: iii Safety Safety Instructions ! The AC plug isolates this equipment from the AC supply. [. . . ] < 5W < 5W < 5W Horizontal Vertical Syne Sync On Off On Off On On Off Off LED On Stand-by Suspend Off Green Amber Amber Amber Factory Preset Timings Resolution 640 x 400 640 x 480 800 x 600 1024 x 768 1024 x 768 1280 x 1024 1280 x 1024 1600 x 1200 1600 x 1200 1920 x 1440 Vertical Frequency (Hz) 70 60 75 75 85 75 85 75 85 75 Horizontal Frequency (KHz) 31. 47 31. 47 46. 88 60. 02 68. 68 79. 98 91. 15 93. 75 106. 00 112. 50 ** All above timings are non-Interlace timings. 3 Chapter 2 Chapter 2 Installing the Monitor This monitor is equipped with an autosensing universal compatible power supply for voltage ranges 100-120/200-240V AC, 50~60Hz. . Please confirm the line voltage designation at the rear panel of the monitor before connecting the machine. 1) Make sure that the system power is turned off. 2) Please refer to the instructions below to connect the signal cable through D-SUB or BNC. 3) Connect the power cord to the monitor and attach it to power source. 4) Turn on the computer and the monitor. 4 Installing the Monitor Connecting the Signal Cable Your Benq P211 provides both D-SUB and BNC signal connectors. The D-SUB or BNC signals can automatically be detected by its microprocessor. Connecting through D-SUB signal connector 1) Make sure that the system power is turned off. 2) Connect the computer end of the D-SUB cable to the 15-pin output connector on the video board of your computer. 3) Connect the monitor end of the D-SUB cable to the D-SUB receptacle on the back of the monitor. 5 Chapter 2 Connecting to An Apple If you connect the monitor to an Apple Macintosh through a D-Sub cable, you need to add the Macintosh adapter to connect the video signal port of your computer and the monitor signal cable. Before connecting the adapter please refer to the user's guide of the adapter to set the switches of the adapter. 6 Installing the Monitor Connecting through BNC Signal Connector 1) Make sure that the system power is turned off. 2) Connect the computer end of the BNC cable to the output connector on the video board of your computer. 3) Connect the monitor end of the BNC cable to the BNC receptacle on the back of the monitor. 7 Chapter 3 Chapter 3 A Look at the Control Panel Menu key : enters or changes Main menus. Enter key : enters sub-menus or selects items. Exit key : goes back to main menus (auto save), or leaves OSD. & key : scrolls the light coloured bar up or down and represents HOT KEY for brightness adjustment. & key : scrolls the light coloured bar left or right and represents HOT KEY for contrast adjustment. i key : is used for Fuzzy Automatic calibration adjustment. 8 A Look at the Control Panel Making Adjustments i key (Fuzzy Auto Calibration ) Just push the i key, then the monitor will automatically adjust display's size and position to the optimum. No re-configuration or adjustment is needed when a user changes display mode. The i key function is different from "Reset" function. "Reset" function for display's geometry, size and position only works under the factory preset timings (please see page 3). The i key function will work under "ANY" display timings which Benq P211 can support. Hot Keys Press or key to adjust contrast directly. Press or key to adjust brightness directly. 9 Chapter 3 OSD Operation 1) Press Menu key to enter or change Main menus (there are three main menus) 2) Press or keys to scroll light coloured bar to desired items. 4) Press , ( , ) key to do the adjustments. If the sub-menu contains 5) 6) keys to scroll light coloured bar to desired multiple items. Then press or key to adjust as required. Press Exit key to save and return to main menus. Press Exit key to save and leave OSD Reset to the factory default settings, please see General Settings Reset and Color Temperature Reset. Main Menu 1 Display Control This main menu includes six items. Scroll the light coloured bar to desired items and press Enter to sub-menus. 10 A Look at the Control Panel Luminance Contrast and Brightness adjustments Contrast adjusts the difference between the light and dark areas. [. . . ] If the two connectors are connected simultaneously, the user can select the desired connector. 18 A Look at the Control Panel Purity Colour purity adjustment To adjust Purity, choose a full white picture and adjust to get a pure white picture at the corner of the screen image. Display Mode Current resolution, horizontal and vertical frequency status presentation. 19 Chapter 3 Timing Setting By making adjustments to your video card settings, you can set the timing and the refresh rate according to your preferences. The monitor will automatically save the settings. Your monitor can accept a vertical frequency ranging from 50 Hz to 160 Hz and an horizontal frequency from 30 KHz to 115 KHz. However, due to different video card and resolution settings, we recommend that you do not exceed the maximum refresh rate, 160 Hz for vertical frequency and 115KHz for horizontal frequency to avoid possible damage to your monitor. [. . . ]