User manual BENQ SM2224

[. . . ] FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. CE Mark Warning This is a Class A product. [. . . ] Make sure you save the settings before you log out 4. Menu-Driven Console Management -69 ARP TABLE SETTING Step 1: Move to highlight [ARP Table] from [IP Networking] and press <Enter>. The screen shows the ARP table entries that have been defined or learned. Add/Delete Static ARP Table Entries Step 2: Press [+] on keypad to add an entry into the ARP Table. Enter Internet/Physical Addresses then. 4. Menu-Driven Console Management -70 Step 3: Press [-] on keypad if you want to delete a static entry from the ARP Table. * No precautionary message appears before you delete an entry from the ARP table. * Be sure you want to delete it before doing so. Search for ARP Table Entries Step 4: Press <S> to search a static entry. You can search by Internet address or physical address. 4. Menu-Driven Console Management -71 4. Menu-Driven Console Management -72 ROUTING TABLE Step 1: Move to highlight [Routing Table] from [IP Networking] and press <Enter>. The screen shows the Routing Table allows you to view, add, delete or search a particular routing path. 4. Menu-Driven Console Management -73 ROUTING TABLE COLUMNS Column Network Mask Gateway Metric VLAN Type Description The IP subnetwork address to which the switch can route packets. The related IP subnetwork mask to which the switch can route packets. The IP address of the router at the next hop. The number of hops needed between the switch and the destination network. The VLAN within which the gateway or destination resides. The IP route type for the IP subnetwork. There are six IP route types: Direct Remote Myself Bcast Mcast Martian Protocol Local NetMgmt ICMP RIP Other A directly connected subnetwork. address on a specific IP A subnetwork broadcast address. A routing entry obtained via ICMP redirect. A routing entry learned via the RIP protocol. A protocol other than one of the other four listed above. Indicates one of the following: 4. Menu-Driven Console Management -74 Add/Delete Routing Table Entries Step 2: Press [+] on keypad to enter Route Options as shown below. Step 3: Press [-] to delete an entry in the routing table. * No precautionary message appears before you delete an entry from the routing table. [. . . ] Please ensure that the network adapter cards installed in the workstation or other devices to the switch are in well working condition. [!] Contact your dealer if problem persists. 8. Trouble Shooting -216 Appendix: Ordering Information Part Number Model 99. 336N2. 001 99. 33228. 001 99. 33228. 002 99. 33228. 003 99. 33228. 004 99. 33228. 005 99. 33228. 006 99. 33228. 007 99. 33628. 001 99. 33628. 002 99. 33628. 003 99. 33628. 004 SM2224 MFF001-SC MFF001-ST MFF001-VF45 Description 24+2 Ports Management Gigabit Ethernet Switch 100Base-FX Fiber Module, Multi Mode, SC connector 100Base-FX Fiber Module, Multi Mode, ST connector 100Base-FX Fiber Module, Multi Mode, VF-45 connector MFF001-MTRJ 100Base-FX Fiber Module, Multi Mode, MT-RJ connector MFF001-SC20 MFF001-SC40 MFF001-SC60 MGL001-SC MGL001-SC10 MGL001-SC20 MGT001-T 100Base-FX Fiber Module, Single Mode 20Km, SC connector 100Base-FX Fiber Module, Single Mode 40Km, SC connector 100Base-FX Fiber Module, Single Mode 60Km, SC connector Gigabit Fiber Module, Multi Mode, SC connector Gigabit Fiber Module, Single Mode 10Km, SC connector Gigabit Fiber Module, Single Mode 20Km, SC connector Gigabit Copper Module 217 Benq Network Products Limited Warranty A. LIMITED WARRANTY Benq Corporation ("Benq") warrants the Benq network product you have purchased from Benq or from an Benq Authorized Reseller to be free from defects in materials and workmanship under normal use during the warranty period of one year from the date of purchase. Your original purchase invoice (sales receipt), showing the date of purchase of the network product, is your proof of the date of purchase. [. . . ]