User manual BERNEX GB21105 CATALOGUE 2010

[. . . ] Changes to the specifications and features in this manual may be made by BERNEX without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without BERNEX's prior written permission. Documentation Classifications In order to assist in the use of this product, BERNEX provides the following types of documentations:    For quick set-up of the product, read the Quick Installation Guide included with the product. For detailed product information, carefully read the User's Manual. For instructions on how to use BERNEX's unique features, read or download the information on/from the Support&Downloads\Motherboard\Technology Guide page on our website. For product-related information, check on our website at: http://www. gigabyte. com. tw Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. [. . . ] After configuring this item, set the password(s) under the Set Supervisor/User Password item in the BIOS Main Menu. Setup A password is only required for entering the BIOS Setup program. (Default) System A password is required for booting the system and for entering the BIOS Setup program. HDD S. M. A. R. T. Capability Enables or disables the S. M. A. R. T. (Self Monitoring and Reporting Technology) capability of your hard drive. This feature allows your system to report read/write errors of the hard drive and to issue warnings when a third party hardware monitor utility is installed. (Default: Enabled) (Note) This item is present only if you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website. - 43 BIOS Setup CPU Multi-Threading (Note) Allows you to determine whether to enable all CPU cores and multi-threading function when using an Intel CPU that supports multi-core technology. This feature only works for operating systems that support multi-processor mode. Enabled Enables all CPU cores and multi-threading capability. PCI Sets the PCI graphics card as the first display. (Default) PEG Sets the PCI Express graphics card as the first display. Init Display First - 45 - BIOS Setup 2-6 Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2009 Award Software Integrated Peripherals x } On-Chip Primary PCI IDE On-Chip SATA Mode PATA IDE Set to SATA Port 0/2 Set to SATA Port 1/3 Set to Azalia Codec Onboard H/W LAN Green LAN SMART LAN Onboard LAN Boot ROM Onboard Serial Port 1 Onboard Parallel Port Parallel Port Mode USB 1. 0 Controller USB 2. 0 Controller USB Keyboard Function USB Mouse Function USB Storage Function [Enabled] [Auto] Ch. 0 Master/Slave Ch. 2 Master/Slave Ch. 3 Master/Slave [Auto] [Enabled] [Disabled] [Press Enter] [Disabled] [3F8/IRQ4] [378/IRQ7] [SPP] [Enabled] [Enabled] [Disabled] [Disabled] [Enabled] Item Help Menu Level  Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults On-Chip Primary PCI IDE On-Chip SATA Mode Enables or disables the first integrated IDE controller. (Default: Enabled) Configures the integrated SATA controller. Disabled Disables the integrated SATA controller. Auto Lets the BIOS set SATA devices to Combined or Enhanced mode. If your onboard SATA controller is automatically configured to Combined mode, you can manually re-configure it to Enhanced mode as needed. (Default) Combined Sets all SATA devices to operate in PATA mode. Combined allows a maximum of 4 ATA devices to be used simultaneously: two PATA devices plus two SATA devices. Enhanced Sets all SATA devices to operate in SATA mode. Non-Combined Sets all SATA devices to operate in PATA mode and disables the integrated IDE controller. PATA IDE Set to SATA Port 0/2 Set to This item is configurable only if the On-Chip SATA Mode is set to Combined. Ch. 0 Master/Slave Sets the IDE channels to Ch. [. . . ] Or go to the Support&Downloads\Technical Service Zone page to submit your question. Our customer service staff will reply you as soon as possible. Appendix - 82 - 5-3 Regulatory Statements Regulatory Notices This document must not be copied without our written permission, and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose. We believe that the information contained herein was accurate in all respects at the time of printing. BERNEX cannot, however, assume any responsibility for errors or omissions in this text. [. . . ]