User manual BERNEX GB21229 CATALOGUE 2010

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without BERNEX's prior written permission.  In order to assist in the use of this product, carefully read the User's Manual.  For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. [. . . ] This item is configurable only if the VGA Core Clock control option is set to Manual. Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU being installed. Allows you to set the CPU North Bridge frequency divisor. && CPU NB Clock Divisor (Note) Core Performance Boost (Note) CPB Ratio (Note) Allows you to determine whether to enable the Core Performance Boost (CPB) technology, a CPU performance-boost technology. (Default: Enabled) Allows you alter the ratio for the CPB. The adjustable range is dependent on the CPU being installed. (Default: Auto) Enables or disables the control of CPU host clock. Auto (default) allows the BIOS to automatically adjust the CPU host frequency. Manual allows the CPU Frequency (MHz) item below to be configurable. Note: If your system fails to boot after overclocking, please wait for 20 seconds to allow for automated system reboot, or clear the CMOS values to reset the board to default values. Allows you to manually set the CPU host frequency. . Options are: Auto (default), 0/64~31/64. && Bank Interleaving Enables or disables memory bank interleaving. Enabled allows the system to simultaneously access different banks of the memory to increase memory performance and stability. (Default: Enabled) ******** System Voltage Optimized ******** && System Voltage Control && DDR3 Voltage Determines whether to manually set the system voltages. Auto lets the BIOS automatically set the system voltages as required. Manual allows all voltage control items below to be configurable. (Default: Auto) Allows you to set memory voltage. Normal Supplies the memory voltage as required. (Default) 1. 100V ~ 1. 900V The adjustable range is from 1. 100V to 1. 900V. Note: Increasing memory voltage may result in damage to the memory or reduce the useful life of the memory. Normal Supplies the CPU voltage as required. (Default) 1. 4000V ~ 1. 7000V The adjustable range is from 1. 4000V to 1. 7000V. [. . . ] Press <Ctrl>+<Y> to set the capacity of the RAID array or press other keys to set the array to its maximum capacity. Press Ctrl-Y to Modify Array Capacity or press any other key to use maximum capacity. . . Figure 3 8. After the creation is complete, the screen will return to LD View Menu where you will see the newlycreated array. 9. Press <Esc> to return to Main Menu and press <Esc> again if you want to exit the RAID BIOS utility. Making a SATA RAID/AHCI Driver Diskette Before installing Windows XP, connect a USB floppy disk drive to your computer first because you need to install the SATA RAID/AHCI driver from a floppy disk that contains the driver during the OS installation. To copy the RAID/AHCI driver for Windows XP, copy all files in the \BootDrv\Hxp folder in the motherboard driver disk to your floppy disk. Installing the SATA RAID/AHCI Driver and Operating System A. Installing Windows XP Restart your system to boot from the Windows XP setup disk and press <F6> as soon as you see the message "Press F6 if you need to install a 3rd party SCSI or RAID driver. " Insert the floppy disk containing the SATA RAID/AHCI driver. [. . . ]