User manual BERNEX GB21229S CATALOGUE 2010

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without BERNEX's prior written permission.  In order to assist in the use of this product, carefully read the User's Manual.  For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. [. . . ] (Default: Enabled) Allows you alter the ratio for the CPB. The adjustable range is dependent on the CPU being installed. (Default: Auto) Enables or disables the control of CPU host clock. Auto (default) allows the BIOS to automatically adjust the CPU host frequency. Manual allows the CPU Frequency (MHz) item below to be configurable. Note: If your system fails to boot after overclocking, please wait for 20 seconds to allow for automated system reboot, or clear the CMOS values to reset the board to default values. Allows you to manually set the CPU host frequency. . This option is configurable only when CPU Host Clock Control is set to Manual. Important It is highly recommended that the CPU frequency be set in accordance with the CPU specifications. Allows you to determine whether to use the preset memory overclocking profile to achieve optimum overclocking performance. (Default: Disabled) Determines whether to manually set the memory clock.  Note: Increasing memory voltage may result in damage to the memory or reduce the useful life of the memory. DDR3 Voltage Determines whether to manually set the system voltages. Auto lets the BIOS automatically set the system voltages as required. Manual allows all voltage control items below to be configurable. (Default: Auto) CPU Voltage Control CPU NB VID Control Allows you to set the CPU voltage. Normal Supplies the CPU voltage as required. (Default) 1. 3625V ~ 1. 6625V The adjustable range is from 1. 3625V to 1. 6625V. Normal CPU Vcore Allows you to set the CPU North Bridge VID voltage. Normal Supplies the CPU NB VID voltage as required. (Default) 1. 1250V ~ 1. 4250V The adjustable range is from 1. 1250V to 1. 4250V. Displays the normal operating voltage of your CPU. Displays the normal operating voltage of your CPU North Bridge. Normal CPU Vcore NB 2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2012 Award Software Standard CMOS Features } } } } } } Date (mm:dd:yy) Time (hh:mm:ss) IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave IDE Channel 2 Master IDE Channel 3 Master Halt On Base Memory Extended Memory Fri, Mar 2 2012 22:31:24 [None] [None] [None] [None] [None] [None] [All, But Keyboard] 640K 941M ESC: Exit F1: General Help F7: Optimized Defaults Item Help Menu Level  Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults Date (mm:dd:yy) Time (hh:mm:ss) Sets the system date. Sets the system time. IDE Channel 0, 1 Master/Slave IDE HDD Auto-Detection Press <Enter> to autodetect the parameters of the SATA device on this channel. [. . . ] Press <Ctrl>+<Y> to set the capacity of the RAID array or press other keys to set the array to its maximum capacity. Press Ctrl-Y to Modify Array Capacity or press any other key to use maximum capacity. . . Figure 3 888 After the creation is complete, the screen will return to LD View Menu where you will see the newlycreated array. 999 Press <Esc> to return to Main Menu and press <Esc> again if you want to exit the RAID BIOS utility. Making a SATA RAID/AHCI Driver Diskette Before installing Windows XP, connect a USB floppy disk drive to your computer first because you need to install the SATA RAID/AHCI driver from a floppy disk that contains the driver during the OS installation. To copy the RAID/AHCI driver for Windows XP, copy all files in the \BootDrv\Hxp folder in the motherboard driver disk to your floppy disk. Installing the SATA RAID/AHCI Driver and Operating System A. Installing Windows XP Restart your system to boot from the Windows XP setup disk and press <F6> as soon as you see the message "Press F6 if you need to install a 3rd party SCSI or RAID driver. " Insert the floppy disk containing the SATA RAID/AHCI driver. [. . . ]