User manual BERNEX GB31119 CATALOGUE 2010

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, orpublished in any form or by any means without BERNEX's prior written permission. „„ In order to assist in the use of this product, carefully read the User's Manual. „„ For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. Example: Table of Contents GA-G41M-Combo Motherboard Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chapter 1 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1-1 1-2 1-3 1-4 1-5 1-6 1-7 Installation Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Options are dependent on CPU FSB and the (G)MCH Frequency Latch settings. Auto sets memory multiplier according to memory SPD data. (Default: Auto) The first memory frequency value is the normal operating frequency of the memory being used; the second is the memory frequency that is automatically adjusted according to the System Memory Multiplier settings. Manual allows all DRAM timing control items below to be configurable. Options are: Auto (default), Manual. DRAM Timing Selectable (SPD) >>>>> Standard Timing Control CAS Latency Time tRCD tRP Options are: Auto (default), 4~11. Options are: Auto (default), 1~63. tRAS - 23 - >>>>> Advanced Timing Control Advanced Timing Control CMOS Setup Utility-Copyright (C) 1984-2012 Award Software Advanced Timing Control x x x x x x tRRD tWTR tWR tRFC tRTP Command Rate (CMD) Auto Auto Auto Auto Auto Auto [Press Enter] [Press Enter] [Press Enter] [Press Enter] ESC: Exit F1: General Help F7: Optimized Defaults Item Help Menu Level  >>>>> Channel A } Channel A Timing Settings } Channel A Driving Settings >>>>> Channel B } Channel B Timing Settings } Channel B Driving Settings Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults tRRD tWTR tWR Options are: Auto (default), 1~15. Options are: Auto (default), 1~3. tRFC tRTP Command Rate(CMD) >>>>> Channel A/B Channel A/B Timing Settings CMOS Setup Utility-Copyright (C) 1984-2012 Award Software Channel A/B Timing Settings x x x x x x x x x x x x x Static tRead Value tRD Phase0 Adjustment tRD Phase1 Adjustment tRD Phase2 Adjustment tRD Phase3 Adjustment Trd2rd(Different Rank) Twr2wr(Different Rank) Twr2rd(Different Rank) Trd2wr(Same/Diff Rank) DIMM1 Clock Skew Control DIMM2 Clock Skew Control DDR Write Leveling DDR Write Training Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto ESC: Exit F1: General Help F7: Optimized Defaults Item Help Menu Level  Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults - 24 - Static tRead Value tRD Phase0 Adjustment tRD Phase1 Adjustment tRD Phase2 Adjustment tRD Phase3 Adjustment Trd2rd(Different Rank) Options are: Auto (default), 1~15. Options are: Auto (default), 0-Normal, 1-Advanced. Options are: Auto (default), 0-Normal, 1-Advanced. Options are: Auto (default), 0-Normal, 1-Advanced. Options are: Auto (default), 0-Normal, 1-Advanced. Options are: None, 360K/5. 25", 1. 2M/5. 25", 720K/3. 5", 1. 44M/3. 5", 2. 88M/3. 5". - 27 - Floppy 3 Mode Support Halt On Allows you to specify whether the installed floppy disk drive is 3-mode floppy disk drive, a Japanese standard floppy disk drive. Options are: Disabled (default), Drive A. Allows you to determine whether the system will stop for an error during the POST. Options are: "All Errors, " "No Errors, " "All, But Keyboard" (default), "All, But Diskette, " "All, But Disk/Key. " These fields are read-only and are determined by the BIOS POST. Memory 2-5 Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2012 Award Software Advanced BIOS Features } Hard Disk Boot Priority Quick Boot EFI CD/DVD Boot Option First Boot Device Second Boot Device Third Boot Device Password Check HDD S. M. A. R. T. Capability CPU Multi-Threading (Note) Limit CPUID Max. to 3 (Note) No-Execute Memory Protect (Note) CPU Enhanced Halt (C1E) (Note) C2/C2E State Support (Note) CPU Thermal Monitor 2(TM2) (Note) CPU EIST Function (Note) Virtualization Technology (Note) Delay For HDD (Secs) Backup BIOS Image to HDD [Press Enter] [Disabled] [Auto] [Floppy] [Hard Disk] [CDROM] [Setup] [Enabled] [Enabled] [Disabled] [Enabled] [Enabled] [Disabled] [Enabled] [Enabled] [Enabled] [0] [Disabled] Item Help Menu Level  Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults Hard Disk Boot Priority Quick Boot Specifies the sequence of loading the operating system from the installed hard drives. EFI CD/DVD Boot Option Enables or disables the quick boot function to speed up the system boot-up process to shorten the waiting time for entering the operating system and to deliver greater efficiency for daily use. (Default: Disabled) First/Second/Third Boot Device Set this item to EFI if you want to install the operating system to a hard drive larger than 2. 2 TB. Make sure the operating system to be installed supports booting from a GPT partition, such as Windows 7 64bit and Windows Server 2003 64-bit. Auto lets the BIOS automatically configure this setting depending on the hard drive you install. (Default: Auto) Specifies the boot order from the available devices. (Note) This item is present only if you install a CPU that supports this feature. [. . . ] - 37 - 2-14 Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2012 Award Software        MB Intelligent Tweaker(M. I. T. )  PC Health Status Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features (Y/N)?Load Save to CMOS and EXIT Y Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save & Exit Setup PnP/PCI Configurations Exit Without Saving : Select Item F10: Save & Exit Setup Save Data to CMOS F11: Save CMOS to BIOS F12: Load CMOS from BIOS ESC: Quit F8: Q-Flash Press <Enter> on this item and press the <Y> key. This saves the changes to the CMOS and exits the BIOS Setup program. Press <N> or <Esc> to return to the BIOS Setup Main Menu. 2-15 Exit Without Saving CMOS Setup Utility-Copyright (C) 1984-2012 Award Software        MB Intelligent Tweaker(M. I. T. ) Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations  PC Health Status Load Fail-Safe Defaults Quit Without Saving (Y/N)?Load N Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup Abandon all Data F11: Save CMOS to BIOS F12: Load CMOS from BIOS ESC: Quit F8: Q-Flash Press <Enter> on this item and press the <Y> key. [. . . ]