User manual BERTAZZONI H366GGVCR

[. . . ] Installation, Service and User Instructions FREESTANDING GAS RANGES BERTAZZONI DIMENSIONS: 36'' (911 mm)(W) x 25 1/8'' (640 mm)(D) x36'' (911 mm)(H) MODELS H366GGVCR H366GGVNE H366GGVVI [M3Y0GTV4D(2 or 5)A] [M3Y0GTV4N(2 or 5)A] [M3Y0GTV4L(2 or 5)A] 310291 IMPORTANT - PLEASE READ AND FOLLOW -Before beginning installation, please read these instructions completely and carefully. -Do not remove permanently affixed labels, warnings, or plates from the product. -Please observe all local and national codes and ordinances. -Please ensure that this product is properly grounded. [. . . ] If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel!Scratches are almost impossible to remove. NOTE: These installation instructions should remain with the unit for future reference. The electrical diagram is located in the backside or the appliance. REPLACEMENT PARTS Only authorized replacement parts may be used in performing service on the appliance. Replacement parts are available from factory authorized parts distributors. Conversion to different types of gas Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply. For Natural Gas fit regulator assembly described in Fig. Adaptation of the pressure regulator for use with different type of gas The pressure regulator supplied with the appliance is a convertible type pressure regulator for use with Natural Gas at a nominal outlet pressure of 4" w. c. or LP gas at a nominal outlet pressure of 11" w. c. and it is pre-arranged from the factory to operate with one of these gas/pressure as indicated in the labels affixed on the appliance, package and Instruction booklet. To convert the regulator for use with other types of gas follow these instructions: 1) Unscrew by hand the upper metal stopper of the regulator. 2) Unscrew by hand the white plastic piece screwed under the above mentioned metal stopper, afterward screw it again in opposite way under the metal stopper (for gas reference see the written "LP" and "NAT" with relative indicating arrows on the white piece). 3) Screw again by hand the metal stopper in the original position on the regulator. Following these exact instructions the gas regulator is converted for use with the other gas/pressure. It is essential that the gasket and the pressure test point stopper are properly installed to avoid gas leakage 12 - CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS: To change the nozzles of the burners use the following procedure: Lift up the burners and unscrew the nozzles ( Fig. ) using an adjustable spanner of 7 mm and change the nozzles with those designed for the new gas supply according to the information given in TABLE shown below. Follow the instructions below to change the oven burner nozzle: 1) Remove the oven level (Fig. 2) Loosen the screw V and pull out the burner from the support being careful not to damage the ignition plug and the thermocouple (Fig. 10-11) using a 10 mm spanner and replace it with the nozzle needed for the new type of gas according to what is indicated in TABLE shown below. Follow the instructions below to change the broiler burner nozzle: 1) Loosen the screw and pull out the burner from the support being careful not to damage the ignition plug and the thermocouple (Fig. 12) using a 7 mm spanner and replace it with the nozzle needed for the new type of gas according to what is indicated in TABLE shown below. 13 Models H366GGV Burner Auxiliary Semi-Rapid Rapid Position Front R Rear L & C Front C Rear R Front L Inner Dual Burner Front L Outer Oven Broiler Oven downside Oven upside [M3Y0GTV4(L, N, D)(2 or 5)A] Gas Type NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) Pressure [i. w. c. ] 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" Max Rate [BTU/h] [W] 3400 996 3400 996 6100 1787 6100 1787 10400 3047 10400 3047 2800 820 2800 820 12000 3516 12000 3516 16000 4688 16000 4688 14500 4248 14500 4248 Min Rate [BTU/h] [W] 900 264 900 264 1500 439 1500 439 2500 732 2500 732 900 264 900 264 4500 1318 4500 1318 4000 1172 4000 1172 Only Max Only Max Only Max Only Max By-pass diam. [mm] Regulated 0, 29 Regulated 0, 36 Regulated 0, 47 Regulated 0, 29 Regulated 0, 65 Regulated 0, 60 No by-pass No by-pass Adapting to different types of gas Injector diam. [mm. ] 0, 90 0, 54 1, 18 0, 70 1, 55 0, 92 0, 80 0, 49 N°2 x 1, 15 N°2 x 0, 70 2, 00 1, 15 1, 90 1, 10 Models H365GGV [M3W0GTV4(L, N, D)(2 or 5)A] Adapting to different types of gas Burner Auxiliary Semi-Rapid Rapid Position Front R Rear L and R Front L Centre Inner Dual Burner Centre Outer Oven Broiler Oven downside Oven upside Injector diam. [mm. ] 0, 90 0, 54 1, 18 0, 70 1, 55 0, 92 0, 80 0, 49 N°2 x 1, 15 N°2 x 0, 70 2, 00 1, 15 1, 90 1, 10 Gas Type NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) Pressure [i. w. c. ] 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" Max Rate [BTU/h] [W] 3400 996 3400 996 6100 1787 6100 1787 10400 3047 10400 3047 2800 820 2800 820 12000 3516 12000 3516 16000 4688 16000 4688 14500 4248 14500 4248 Min Rate [BTU/h] [W] 900 264 900 264 1500 439 1500 439 2500 732 2500 732 900 264 900 264 4500 1318 4500 1318 4000 1172 4000 1172 Only Max Only Max Only Max Only Max By-pass diam. [mm] Regulated 0, 29 Regulated 0, 36 Regulated 0, 47 Regulated 0, 29 Regulated 0, 65 Regulated 0, 60 No by-pass No by-pass CAUTION: save the orifices removed from the appliance for future use REGULATION OF BURNERS Primary air adjustment: Oven burner adjustment: follow the instructions below to adjust the primary air for the over burner: 1) Remove the oven bottom. 2) Loosen the screw P and adjust the position X of the Venturi cone (Fig. [. . . ] Cleaning the work surface: periodically clean the burner heads, the cast iron pan supports and the burner caps using warm water. Any spillage must always be removed as soon as possible using a rag. If it become difficult to open or close a valve, do not force it, but immediately request the assistance of the technical service personnel. Cleaning the colored parts: The special finishing of the Bertazzoni Color ranges is realised with a particular painting Follow these instructions for a correct maintenance of Your Bertazzoni range : - Always use a very soft sponge or cloth. [. . . ]