User manual BERTAZZONI X244GGVX

[. . . ] Installation, Service and User Instructions FREESTANDING GAS RANGES BERTAZZONI DIMENSIONS: 24'' (605 mm)(W) x 25 1/8'' (640 mm)(D) x36'' (911 mm)(H) MODEL X244GGVX [MLS0GTU4X(2 or 5)A] 310287 IMPORTANT - PLEASE READ AND FOLLOW -Before beginning installation, please read these instructions completely and carefully. -Do not remove permanently affixed labels, warnings, or plates from the product. -Please observe all local and national codes and ordinances. -Please ensure that this product is properly grounded. [. . . ] In case of doubt, do not use the appliance and contact skilled personnel. Keep all the packing parts (polystyrene foam, cardboard, staples, etc. ) away from children. Consider the critical dimensions of the appliance, before making an opening in the top surface of the bench top. (relative measurements as per Fig 1- 2). fig. 1 fig. Overhead clearances (Minimum values) The minimum overhead clearances shall be in accordance with the minimum values indicated in the table n. 1 and are shown and in the fig. 1- 2 Range hoods and exhaust fans shall be installed in accordance with the manufacturer's instructions. However, in no case shall the clearance between the top of the highest burner of the cooking appliance and the range hood be less than 30"( 762mm). Any other downward facing combustible surface less than 600mm above the top of the highest burner shall be protected for the full width and depth of the cooking surface area. However, in no case shall this clearance to any surface be less than 173/4"(450mm. ) Maximum depth for the overheads cabinet is 13" (330mm) 3 2. Side clearances (Minimum values) The different side clearances shall be in accordance with the minimum values indicated in the table n. 1 and are shown and in the fig. 1 The cooking surface area is defined as that part of the appliance where cooking normally takes place and does not include those parts of the appliance containing control knobs. Clearances inches (mm) L1 L2 L3 L4 L5 L6 L7 L8 L9 18 7/8" (480) 1 9/16" (40) 3 3/8" (86) 18" (457) 24" (610) 13" (330) 23 1/4" (590) 3/4" L10 L11 W D B1 (*) B2 (*) B3 (*) B4 (*) R 22 1/2" (570) 32" (813) 23 1/4" (590) 19 2/3" (500) 1 3/8" (35) 3 1/2" (90) 3" (76) 3 1/2" (90) 5 1/8"(135) (20) 3 15/16" (100) (*) Note: -B1 is the min. clearance between the front edge of the appliance and the front edge of the cabinet. clearance between the left/right side edge of the appliance and the side wall (if present). clearance between the back edge of the appliance and the back wall. Attaching the hotplate To prevent liquids from leaking accidentally into the underlying storage space, the appliance is equipped with a special gasket. To apply this gasket, carefully follow the instructions in Fig. Lay out the protective sealing strips along the edges of the opening in the bench top and carefully overlap the strip end. insert the hotplate into the bench top opening. With a screwdriver assemble the brackets A to the hotplate bottom by means of the screws B. Slide the hooks into position and secure them with the screws. Trim the part of the sealing strips which extend beyond the hotplate base fig. 3 Gas connection fig. 4 Before connecting the appliance to the gas supply, first remove the plastic plug on which is pressfitted into the gas inlet union; to remove, just pull it off. Check the `gas type' sticker attached to the hotplate. [. . . ] - Quand vous cuisinez des mets avec de l'huile ou de la graisse, qui sont très inflammables, l'utilisateur ne devra pas laisser l'appareil sans surveillance. 21 ATTENTION: Si l'alimentation est découpée, les brûleurs peuvent être allumés avec des allumettes. Les brûleurs équipés d'un thermocouple de sécurité peuvent seulement être allumés lorsque le bouton est en position de MAXIMUM (gravure de flamme large). Avertissement: L'utilisation d'un appareil de cuisson à gaz produit de la chaleur et de l'humidité dans la chambre où il est installé. [. . . ]