User manual BESAFE IZI COMFORT ISOFIX

[. . . ] Make sure that the floor support is fully pushed down. · When installed with ISOfix: Make sure the indicators are green before you drive. · When the child weighs over 18 kg or the shoulder height grows above the highest position of the shoulder straps, the child must change to a group 2/3 seat. · After an accident, the seat must be replaced. [. . . ] 3- Unlock the belt clamps and unlock the car belt. 4- Remove the car belt and remove the seat from the vehicle. Removing the seat Positioning of the child 1- Position of the shoulder straps: Check that the shoulder strap slots are levelled with your child's shoulders (16). too high (16) too low 2- The height of the shoulder straps and the head rest can be adjusted by releasing the release handle at the back of the head rest and pulling the head rest up or down while keeping the head rest upright (17). correct (17) 3- Pull the shoulder straps up while pressing the button of the central adjuster (18). (18) 4- Open the harness buckle. 10 11 5- Position the shoulder straps over the orange marking at sides of the seat to keep the harness open while you position the child (19). (19) Removing and refitting the cover · Make sure that the harness straps are fixed in the right way, after fitting the cover. ! 6- When the child is positioned, place the shoulder straps over the child's shoulders and close the buckle: CLICK!(20). (20) Removing the cover 1- Pay attention when you remove the cover, as fitting the cover is done in the opposite way. 2- To remove the seat cover, the harness straps must be released at both sides. See red circle (23). 7- Pull the harness strap through the central adjuster in the direction of the green arrow straight up-/forwards. Continue pulling until the harness is a comfortable but firm fit. The belt tension indicator will show green (21). (21) (23) 3- Start to take off the lower seat part and unhook both harness straps from the metal belt hooks. 4- The cover of the head rest can be taken off separately by disconnecting the hooks at the backside and pulling off the fabric to the front. (22) ! Make sure that the harness straps are always locked and tightened when the child is in the seat. Sleeping position · The seat has 4 reclining positions. · By turning the reclining knob, the seat can be put in another position (22). 12 13 Refit the cover 1- Pull the head rest in the highest position. Mount the head rest cover and connect the hooks at the back side. Pull the harness straps through the holes. Connect the loose bottom part of the head rest fabric with the plastic part under the head rest. 2- Pull the harness straps through the opening of the seat cover and lock the harness buckle. Pull the crotch strap through the opening of the seat part. 3- Pull the loops of the harness straps from the bottom of the seat part through the openings to the hooks in the bottom of the seat. Hook both harness straps on the metal belt hooks and pull the straps firmly to ensure that they are correctly installed (24). Cleaning instructions · The cover of the seat must be washed according to the instructions on the inside of the cover (25). (25) wash with similar colours · DO NOT use any aggressive cleaning products; these may harm the construction material of the seat. (24) Warning: potential misuse · It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG. · Install only with 3-point car belts, approved to UN/ECE Regulation No. 16 or other equivalent standards (26). (26) ! 4- Mount the top part and then the shoulder parts. Mount the seat part and bring the seat cover under the rear parts of the sidewalls. shoulder belt OK hip belt NO 14 15 ! DO NOT leave any space between the back of the seat and the seat of the vehicle (27). (27) Important advice · DO NOT attempt to dismantle, modify or add any part to the seat. Warranty will expire if non-original parts or accessories are used. · DO NOT use anything, such as a cushion, to raise the child seat off the passenger seat of the vehicle. [. . . ] · The guarantee is only valid when you use your seat appropriately and with care. Please contact your dealer, he will decide if the seat will be returned to the manufacturer for repair. Replacement or return cannot be claimed. The guarantee does not get extended through repair. [. . . ]