User manual BESAFE IZI KID ISOFIX

[. . . ] · When installed with ISOfix: Make sure the indicators are green before you drive. · We recommend to use the seat as long as possible in the rearward-facing installation. · We recommend that this seat is used only for children who can sit upright, so not younger than 6 months. · For children under 1 year and/or under 10 kg weight, we recommend that the most reclined sitting position and the body hugger and seat cushion are used. [. . . ] Removing the seat 1- If the seat is installed in the back seat of the vehicle, push the front seat of the vehicle forward as much as possible 2- Move the front brace inwards with the ratchet, not further than the stop sign. ! 14- Lock the floor support with the locking bolt (11). (11) 3- Remove the locking bolt from the floor support, adjust the floor support in the highest position and lock again with the locking bolt. 4- Release the ISOfix connectors by pressing the release mechanism on the ISOfix connectors. The indicators will show red when the ISOfix connectors are released (13). (13) 16- Positioned in the back seat of the vehicle, you should, if possible, push the front seat of the vehicle backwards, so that it is in contact with the child seat. If it is not possible to obtain contact with the child seat, push the back rest of the front seat of the vehicle forward so that the distance between child seat and back rest of the front seat of the vehicle is minimum 25 cm. Positioned in the front seat of the vehicle, you should position the seat against the dashboard. (12) 5- Push the switch on each side and push the ISOfix connectors into the base (14). (14) 6- Pull the seat back towards the front. Turn the seat so you can easily remove the seat. 7- Remove the insertion clips from the vehicle. Place them under the base of the child seat. 8 9 Positioning of the child 1- Position of the shoulder straps: Check that the shoulder strap slots are levelled with your child's shoulders (15). too high (15) 5- Position the shoulder straps over the orange marking at sides of the seat to keep the harness open while you position the child (18). (18) too low correct 2- The height of the shoulder straps and the head rest can be adjusted by releasing the release handle at the back of the head rest and pulling the head rest up or down while keeping the head rest upright (33). 6- When the child is positioned, place the shoulder straps over the child's shoulders and close the buckle: CLICK!(19). (16) (19) 7- Pull the harness strap through the central adjuster in the direction of the green arrow straight up-/forwards. Continue pulling until the harness is a comfortable but firm fit. The belt tension indicator will show green (20). (17) (20) 3- Pull the shoulder straps up while pressing the button of the central adjuster (17). Make sure that the harness straps are always locked and tightened when the child is in the seat. ! Sleeping position · The seat has 4 reclining positions. · By pulling the reclining lever upwards, the seat can be put in another position (21). (21) 4- Open the harness buckle. 10 11 Removing and refitting the cover Refit the cover 1- Pull the head rest in the highest position. Mount the head rest cover and connect the hooks at the back side. Pull the harness straps through the holes. Connect the loose bottom part of the head rest fabric with the plastic part under the head rest. 2- Pull the harness straps through the opening of the seat cover and lock the harness buckle. Pull the crotch strap through the opening of the seat part. ! · Make sure that the harness straps are fixed in the right way, after fitting the cover. Removing the cover 1- Pay attention when you remove the cover, as fitting the cover is done in the opposite way. 2- To remove the seat cover, the harness straps must be released at both sides. See red circle (22). 3- Pull the loops of the harness straps from the bottom of the seat part through the openings to the hooks in the bottom of the seat. Hook both harness straps on the metal belt hooks and pull the straps firmly to ensure that they are correctly installed (23). (23) (22) 3- Start to take off the lower seat part and unhook both harness straps from the metal belt hooks. 4- The cover of the head rest can be taken off separately by disconnecting the hooks at the backside and pulling off the fabric to the front. 4- Mount the top part and then the shoulder parts. [. . . ] · BeSafe advises that child seats should not be bought or sold second-hand. · KEEP this user manual for later use with the seat. · DO NOT use the seat for longer than 5 years. Due to ageing, the quality of the material may change. [. . . ]