User manual BIAMP MEQ 152 AND 301

[. . . ] When released (out), these switches bypass the equalization. When depressed (in), these switches activate the equalization. Use EQ Bypass to compare equalized signals to un-equalized signals. Filter Controls: These slide controls adjust the gain in each of the filter bands (25Hz~16kHz/channel). [. . . ] The controls have a center detent (flat). Master Gain Controls: These slide controls adjust the overall gain of the repective channels only when the EQ Bypass Switches are depressed (in). Use these controls to compensate for changes in gain due to filter adjustments. REAR PANEL 27V 50/60 Hz ~ BIAMP SYSTEMS PORTLAND, OREGON output input output input an affiliate of Rauland-Borg Corp 15 watts class 2 wiring MADE IN U. S. A. channel 2 channel 1 AC Power Cord: The external power transformer provides 27 Volts AC to the equalizer, and is detachable via a 5-pin DIN connector. The equalizer has two internal `self-resetting' fuses (there are no user servicable parts inside the unit). If the internal fuses blow, they will attempt to re-set after a short period. However, this may be an indication that the equalizer requires service. Outputs: These plug-in barrier strip connectors provide balanced output from the respective channels. For unbalanced output, connect to the Outputs with high to (+) and ground to ( ), leaving (-) unconnected. Signal levels will be reduced by 6dB when the Outputs are unbalanced. Inputs: These plug-in barrier strip connectors provide balanced input to the respective channels. Signal levels will be reduced by 6dB when the Output is unbalanced. Input: This plug-in barrier strip connector provides balanced input to the equalizer. For unbalanced input, connect to the Input with high to (+) and ground to both (-) & ( ). 3 SPECIFICATIONS mEQ152 Frequency Response (20Hz-20kHz @ +4dBu): Total Harmonic Distortion (20Hz-20kHz @ +4dBu): Intermodulation Distortion (SMPTE): Noise Floor (20Hz-20kHz @ unity gain w/ filters flat): Maximum Input Level: Input Impedance (balanced): Maximum Output (600 ohm load): Output Impedance (balanced): Power Consumption: Power Requirements: Dimensions: Height (1 rack space) Width Depth Weight: 1. 75" (44mm) 19" (483mm) 7. 25" (184mm) 6 lbs. (2. 72kg) +0, -0. 5dB < 0. 008% < 0. 008% -85dBu +24dBu 20k ohms +21dBm 200 ohms < 12 Watts 115/230VAC 50/60Hz mEQ301 +0, -0. 5dB < 0. 008% < 0. 008% -82dBu +24dBu 20k ohms +21dBm 200 ohms < 10 Watts 115/230VAC 50/60Hz 1. 75" (44mm) 19" (483mm) 7. 25" (184mm) 6 lbs. (2. 72kg) 4 WARRANTY BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL. BIAMP Systems expressly warrants this product to be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase as a new product from an authorized BIAMP Systems dealer under the following conditions. In the event the warranted BIAMP Systems product requires service during the warranty period, BIAMP Systems will repair or replace, at its option, defective materials, provided you have identified yourself as the original purchaser of the product to any authorized BIAMP Systems Service Center. Transportation and insurance charges to and from an authorized Service Center or the BIAMP Systems factory for warranted products or components thereof to obtain repairs shall be the responsibility of the purchaser. This warranty will be VOIDED if the serial number has been removed or defaced; or if the product has been subjected to accidental damage, abuse, rental usage, alterations, or attempted repair by any person not authorized by BIAMP Systems to make repairs; or if the product has been installed contrary to BIAMP Systems's recommendations. Electro-mechanical fans, electrolytic capacitors, and the normal wear and tear of appearance items such as paint, knobs, handles, and covers are not covered under this warranty. [. . . ] Electro-mechanical fans, electrolytic capacitors, and the normal wear and tear of appearance items such as paint, knobs, handles, and covers are not covered under this warranty. BIAMP SYSTEMS SHALL NOT IN ANY EVENT BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING LOST PROFITS, LOSS OF USE, PROPERTY DAMAGE, INJURY TO GOODWILL, OR OTHER ECONOMIC LOSS OF ANY SORT. EXCEPT AS EXPRESSLY PROVIDED HEREIN, BIAMP SYSTEMS DISCLAIMS ALL OTHER LIABILITY TO PURCHASER OR ANY OTHER PERSONS ARISING OUT OF USE OR PERFORMANCE OF THE PRODUCT, INCLUDING LIABILITY FOR NEGLIGENCE OR STRICT LIABILITY IN TORT. [. . . ]