Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BIAMP RP-C2. We hope that this BIAMP RP-C2 user guide will be useful to you.
Lastmanuals help download the user guide BIAMP RP-C2.
Detailed instructions for use are in the User's Guide.
[. . . ] RP-C2 - Remote Panel (Input Connectors)
Instruction Manual
RP-C2 (Biamp #909-0171-00): The RP-C2 is a remote panel, which consists of one XLR and two RCA input jacks mounted on a grey `decorator' style cover plate, with a single-gang `cut-in' style PVC electrical back-box and barrier-strip wiring connector. An internal transformer and resistors provide summing, balancing, and isolation for the RCA inputs. [. . . ] This provides a 6dB increase in output level from the transformer. For a 1:2 ratio, move the J4 jumper strap one pin towards the rear of the circuit board, to the "1:2" position, using needle-nose pliers. A 1:2 ratio may help compensate for low-level sources or signal loss in long cables.
RCA
transformer
Output Connector: This plug-on barrier-strip connector provides the output signals from the RP-C2, for connection to inputs on the associated products. A common ground connection is used for both the XLR and RCA outputs. Each output connection is balanced, providing both a positive (+) and a negative (-) terminal. The unbalanced stereo RCA input signals are resistively summed into mono, then passed through a transformer for balancing and isolation.
XLR
Biamp Systems, 10074 S. W. Arctic Drive, Beaverton, Oregon 97005 U. S. A.
an affiliate of Rauland-Borg Corp.
(503) 641-7287
www. biamp. com
output connector
Back-Box Installation
Back-Box
flange
Remove the back-box from the front panel (controls). Route cables through a `knock-out' hole on the rear of the back-box. Install the back-box in a wall or panel, in the same orientation as any standard single-gang electrical box. The mounting surface may be from 1/8" to 1" thick. (3. 175mm to 25. 4mm) The mounting cavity must be exactly 3. 6" high, 2. 25" wide, and at least 2. 75" deep. (91. 44mm H x 57. 15mm W x 69. 85mm D) Insert the back-box into the wall or panel, then tighten the flange screws until the flanges hold the box securely in place. [. . . ] An alternative is to utilize a double-wide electrical back-box, which has the additional space for an RIK.
knock-outs
flange
RP-C2 Block Diagram
2 3 1
+ + -
585. 9171. 00
Biamp Systems, 10074 S. W. Arctic Drive, Beaverton, Oregon 97005 U. S. A.
an affiliate of Rauland-Borg Corp.
(503) 641-7287
www. biamp. com [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BIAMP RP-C2
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BIAMP RP-C2 will begin.
