User manual BIAMP VOCIA END OF LINE DEVICE

[. . . ] 8 2 VOcia EnD Of LinE DEVicE (ELD-1) The Vocia® End of Line Device (ELD-1) is a networked safety device for use with a Vocia amplifier (e. g. , VA-8600) and an integral part of standard-compliant voice evacuation and mass notification systems. The ELD-1 tests speaker line integrity between the Vocia amplifier and the ELD-1. [. . . ] The RJ45 connector provides two LEDs that indicate Ethernet link and network activity. 4 ELD-1 sEtup anD usE Speaker Line Connector A plug-in barrier-strip connector on the ELD-1 connects the device to the end of the speaker line. The device needs to be connected to an appropriate monitoring point on the speaker cable--typically after the last speaker on the run. The connector provides for both constantvoltage (70V, 100V) and low-impedance circuits. Connect the speaker line to the appropriate input for the circuit configuration. Please note: For higher-resolution detection, a constant-voltage line may be connected to the Lo-Z input, although the ELD-1 will represent a 1-watt load to a 100V circuit and a 0. 5-watt load to a 70V circuit. The user should not connect Lo-Z circuits to the 70/100V input. 70V/100V Lo-Z Com End of Speaker Line 5 ELD-1 instaLLatiOn Installation The ELD-1 may be mounted in a rack or on a wall using four screws at the end of the flanges or two screws in the keyholes on the rear. Please install the unit away from heat sources, such as vents and radiators, and in rooms with adequate ventilation. Do not exceed the maximum operating temperature of 113 degrees F (45°C). An ELD-1 should be connected at the end of every speaker line that is to be monitored. The diagram below shows the appropriate connection to the speaker wire and the network. In EN54-16 compliant systems, the ELD-1 must be connected to a compliant Ethernet switch that is backed by an uninterruptible power supply (UPS). Rack UPS ELD-1 UPS ELD-1 ELD-1 Ethernet Switch ELD-1 Vocia Amplifier 8600 585. 0263. 90A 6 ELD-1 spEcificatiOns End of Line Device 1 SPECIFICATIONS SpeakerLineInputConfiguration: Speaker Line Input Impedance: Balanced and Floating (transformer coupled) 70/100V Input: >100k Low-Z Input: 10k Power: Overall Dimensions: Height: Width: Depth: Weight: Ambient Operating Temperature Range: 802. 3af (PoE) Class 1 1. 06 inches (27mm) 6. 0 inches (153mm) 3. 07 inches (78mm) Approx 0. 66 lbs. (300g) Maximum Input Level (AC): System Headroom: Adjustable in 1dB steps over a 30dB range 70/100V Input: 200V Low-Z Input: 100V 32-113 degrees F (0-45 degrees C) EU Directive 2002/95/EC, RoHS directive CE marked Connection: RJ45 with shielded Ethernet/PoE cable (CAT5, CAT5e, CAT6, or CAT7) Compliance: End of Line Device 1 BLOCk DIAgRAm 70/100V Low Z Vocia System control data PAD XFMR A/D Host Processor PoE 7 ELD-1 warranty BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1. BIAmP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAmP Systems dealer, subject to the terms and conditions set forth below. [. . . ] Statements, representations or warranties made by any dealer do not constitute warranties by BIAmP Systems. BIAmP Systems shall not be responsible or liable for any statement, representation or warranty made by any dealer or other person. [. . . ]