User manual BILLION BIPAC 2AB 2.0

[. . . ] 2 BIPAC-2AB 2. 0 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CHAPTER 2 4 Using BIPAC-2AB 2. 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A typical modem transmission has a rate of 56Kbps (kilobits per second or thousand bits per second). ISDN digital technology allows transfer rates of up to 128Kbps. Because ISDN transmits data digitally, the data is virtually error free, and the transmission is much clearer, with fewer interruptions and slowdowns in facsimile transmissions. With ISDN devices implemented throughout the world, a truly digital network will emerge, allowing everyone fast and easy access to the global information highway. BIPAC-2AB 2. 0 User's Manual The BIPAC-2AB 2. 0 ISDN a/b Adaptor The BIPAC-2AB 2. 0 ISDN a/b adaptor allows you to make the transition from analog to digital without having to discard all your present analog devices. The BIPAC-2AB 2. 0 provides an interface between your ISDN line and present analog devices such as your telephone. With a full array of convenient functions such as call waiting, call holding, call transfer, call forwarding and speed dialing among others, your BIPAC-2AB 2. 0 will help you step from the world of analog communications right into the 21st century world of ISDN! BIPAC-2AB 2. 0 FIGURE 1: THE BIPAC-2AB 2. 0 ISDN A/B ADAPTOR Package Contents The BIPAC-2AB 2. 0 package comes with the following accessories: 1. The BIPAC-2AB 2. 0 external ISDN a/b adaptor 2 Chapter 1 Introduction 2. This User's Manual BIPAC-2AB 2. 0 Features The BIPAC-2AB 2. 0 supports many standard and enhanced features that allow you to make full use of ISDN services with your existing analog devices, including the following: Caller ID Individual phone number (MSN) for each analog port Password-protected for configurations Inter-call Call waiting Call hold/retrieve Internal call transfer Internal call forwarding Call suspend/resume Supports "keypad protocol" for supplementary services Speed dialing Call filter Do not disturb Distinct ring pattern for different MSN 3 Chapter 2 Using BIPAC-2AB 2. 0 Before Connecting Make sure that you have all you need to connect the BIPAC-2AB 2. 0 ISDN a/b adaptor. At least one analog telephone (or other analog device) 2. A power outlet that supplies 220 ~ 240 volts AC 3. An ISDN basic rate S0 interface released by PTT (Post, Telephone and Telegraph administration) Connecting the BIPAC-2AB 2. 0 Please refer to the following instructions and figures for installation procedures: 1. Connect one or two analog telephones (or other analog devices) to the RJ-11 jacks labeled "a/b 1" or "a/b 2" on the back of the BIPAC-2AB 2. 0. Connect your ISDN line to the RJ-45 jack labeled "ISDN S0" on the back of the BIPAC-2AB 2. 0. Plug the power adaptor into the power outlet. The POWER LED will illuminate on the front panel. Chapter 2 Using BIPAC-2AB 2. 0 FIGURE 2: CONNECTING THE BIPAC-2AB 2. 0 4. The BIPAC-2AB 2. 0 ISDN a/b adaptor will run a Power-On selfdiagnostic test. The LEDs on the front panel will blink on and off one by one and the connected analog telephones will ring. The Front Panel LEDs The following illustration and table describe the front panel LEDs: FIGURE 3: THE FRONT PANEL LEDS LED PWR RUN ISDN B1 B2 Meaning When lit it indicates AC power is connected. Flashes periodically to indicate that the BIPAC-2AB 2. 0 is working properly. [. . . ] Disconnect and then Retrieve To disconnect an active call and then retrieve a call that has been put on hold, use the following command line: *0 # Make a New Call Hold/ Retrieve 9 BIPAC-2AB 2. 0 User's Manual Call Waiting If you have an active call and the Call Waiting function is enabled, you will hear two tones when there is another incoming call. You can switch between the two calls by using the Hold/Retrieve function (* # ). To transfer a call to the other analog port of the ISDN TA, you can first put the call on hold by pressing: *# Then, make an internal call with the following command: # After you put the telephone handset on-hook (hang up), the call will be transferred to the other port. [. . . ]