User manual BINATONE IDECT X2

[. . . ] USER GUIDE iDECT X2 System DIGITAL CORDLESS TELEPHONE THIS EQUIPMENT IS NOT DESIGNED FOR MAKING EMERGENCY TELEPHONE CALLS WHEN THE POWER FAILS. ALTERNATIVE ARRANGEMENTS SHOULD BE MADE FOR ACCESS TO DIAL EMERGENCY SERVICES. Ver. 1, Jul 06 (BTP) Before operating this set, please read these instructions carefully. BINATONE " iDECT X2 System " User Guide - Back Page BINATONE " iDECT X2 System " User Guide - Front Page 1)White background and black letters 2)Material: 60lb Book Paper 3) Size: 105mm(w) x 148mm(H) A6 Important note -- emergency calls The iDECT X2 is not designed for making emergency calls if the mains power fails. So you should make alternative arrangements for access to Emergency Services. [. . . ] Press the MENU/OK button to confirm è You will hear a long confirmation beep sound Press and hold the HANG UP button to go back to standby mode Press the MENU button then the â button Three. è Display Shows Main Menu >Advanced Set Press the MENU/OK button then the â button Twice. è Display Shows Advanced Set >Call log Press the MENU/OK button then the button or â bottun to select the All calls and Missed Calls. Press and hold the HANG UP button to go back to standby mode. â 2 3 4 To delete all 1 caller display records 2 3 4 5 To use the call log 1 2 3 4 24 Color profile: Disabled Composite Default screen Using a multi-handset system If you have an iDECT X2 multi-handset system, you already have more than one handset registered to your base unit. You can register additional handsets -- up to four per base unit. With two or more handsets, you can: make intercom calls from one handset to another transfer an outside call from one handset to another shuttle between an outside call and an intercom call set up a three-way conference call Each handset's number (1 to 4) is shown on its display. To make an 1 intercom call Press and hold the INT/# button for 2 seconds. è The INT symbol flashes on the display and the numbers of the available handsets will be displayed INTERCOM 2 3 4 Press the appropriate number to select and call the handset è The other handset rings, and its display shows Call From Handset # (with your handset number). When the other handset user answers, you'll be connected. On either phone, press the HANG UP button or replace the unit in the base unit or charger pod 2 To end an intercom call 25 Color profile: Disabled Composite Default screen Using a multi-handset system To answer an intercom call The ringing tune for intercom calls is different from that for outside calls. When someone makes an intercom call to you, your handset's display shows INTERNAL FROM # with the number of the handset calling you. Press the speakerphone button to answer When you're talking on an outside call (a call you've either made or answered), you can transfer it to another handset: To transfer a call 1 Press and hold the INT/# button until Intercom flashes on the display. Then key in the number of the other handset è The outside call is put on hold and the other handset rings. When the other handset user answers, you can speak to her/him. If the other user does not answer, you can get back to the outside call at any time by pressing and holding the INT/# button again. 2 Press the HANG UP button to hang up and transfer the call If you prefer, you can press HANG UP to transfer the outside call before the other handset answers your intercom call. If the user hasn't answered after 30 seconds, the outside call will come back to you and your handset will ring. 26 Color profile: Disabled Composite Default screen Using a multi-handset system To shuttle between two calls When you have made or answered an outside call and then made an intercom call, you can shuttle from one to the other, like this: Press and hold the INT/# button for one second to speak to each in turn, putting the other on hold You can transfer the outside call to the other handset by pressing HANG UP while you're connected to the intercom call If you press HANG UP while you're connected to the outside call, you'll disconnect it. To set up a three-way conference 1 2 Make or answer an outside call Press and hold the INT/# button to start intercom mode then key in the number of the other handset è The outside call is put on hold and the other handset rings. When the other user answers: Press the INT/# button for one second Use the BACK/MUTE key to turn off the handset microphone and the á or â button to adjust the volume. 3 To end the conference Press the HANG UP button è You will drop out of the conference call, leaving the other user connected to the outside call. 27 Color profile: Disabled Composite Default screen Using a multi-handset system New Call tone When you are on an intercom call and an outside call comes in, you'll hear New Call tone to tell you that someone is calling you. To answer the outside call and end the intercom call: Press the PHONE button briefly OR, to answer the outside call and put the intercom call on hold (so you can later use shuttle, conference or transfer): Press the INT/# button for one second If you now want to set up a three-way conference, simply press and hold the INT/# button for one second. To page all handsets from the base unit To make all registered handsets ring (this is useful if you've forgotten where you put a handset): 1 Press the HANDSET LOCATOR button on the base unit è The handsets ring for up to 20 seconds and their displays show <Paging>. To stop the ringing before 20 seconds: EITHER press the HANDSET LOCATOR button again OR press any button on any handset 28 Color profile: Disabled Composite Default screen Custom settings The iDECT X2 can be customised to suit your preferences in a number of ways. Some of these functions have been covered earlier in this User Guide. This section is a roundup of items that have not yet been mentioned. When making a change to a setting you can press the HANG UP button at any point to cancel what you're doing and go back one step. When you're keying in numbers, if you make a mistake, press the HANG UP button to delete digits. [. . . ] The port (connected to the telephone line) is a TNV port with respect to EN41003. PBX compatibility Timed break recall: adjustable to 100 ms (default), 270 ms, 380 ms or 600 ms. Pause length (using the button): 3 seconds. Signalling type: DTMF (dual-tone multifrequency, also called tone dialling); or loop disconnect (pulse dialling). [. . . ]