User manual BINATONE LYRIS 110

[. . . ] it is not close to a sink, bath or shower, or anywhere else where it might get wet. it is not close to other electrical equipment - fridges, washing machines, microwave ovens, TVs, fluorescent lights, etc. Plug the coiled handset cord into the Handset. Plug the other end into the jack on the left side of the Base unit. [. . . ] Ringer light - This flashes when the phone is ringing for an incoming call. M1, M2 and M3 one -Touch Memory Buttons 3. P(Pause) button 1 2 Storing a Number in M1, M2, M3 one-touch memories 1 2 Lift up Handset, press STO (store)button . 5. Technical details Standard Temperature range PBX compatibility Lyris 110 Telephone Operating 0 ºC to 40 ºC Storage -20 ºC to 60 ºC Timed break recall: 100 ms. Signalling type: DTMF (dual-tone multifrequency) also called tone dialing. Network connection This equipment is intended to be used in the UK only. Operation on other countries' PSTN termination points cannot be guaranteed . Contents of this User Guide 1. Where to find it 3 3 2 Key in the telephone number you wish to stored. Press M1, M2 and M3 button to store the number in the selected memory. The largest length cannot exceed 15 digits and if exceed, the memory will not store the correct number. Lift up Handset, press STO (store)button. Key in the telephone number you wish to stored. Up to a maximum 15 digits. Press the 0-9 button to store the number in the selected memory. 2 . Technical details Pressing buttons on your phone When the instructions in this user guide tell you simply to `press ' a button, this means that you should press the button briefly, then release it. When the instructions tell you to `press and hold' a button, this means you should keep the button pressed until the display changes and / or you hear a tone. Storing a Number in (0-9) two-touch memories 1 2 3 Replace the Handset on the Base unit cradle. Dial out Stored number 3 Lift up Handset, press M1, M2, M3 buttons. 2 The phone automatically redials numbers. BINATONE TELECOM PLC 1 Apsley Way London NW2 7HF, United Kingdom. Tel: +44(0) 20 8955 2700 Fax: +44(0) 20 8344 8877 e-mail: binatoneuk@binatonetelecom. co. uk Connection and conditions for use ________________________________________ . Dial out Stored number (0-9) two-touch memories 1 2 Pd Y^Va V cjbWZg hidgZY ^c P ld1idjX] bZbdgn . 41=/ C Lift up the handset. C w:-;; <0- `Y`bdj *=<<76Ztmt[ C r-A 16 <0- 5-57:A 47+ ~<176 6=5*-: Z_]h[ EC Declaration of Conformity Binatone Telecom Plc 1 Apsley Way London NW2 7HF, United Kingdom. Declare under our sole responsibility that the following product Type of equipment: Model Name: Country of Origin: Brand: Corded Phone Lyris 110 China Binatone We the manufacturer / Importer : You can connect your Lyris 110 phone to a direct exchange line (DEL) - a line connected to a local exchange, with its own phone number; to an extension socket connected to a DEL; or to an extension on an approved compatible PBX. Do not connect the Lyris 110 phone as an extension to a pay phone. The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc. ) connected to an exchange line must not add up to more than 4 - otherwise, one or more of them may not ring and/or answer calls correctly. The Lyris 110 phone has a REN of 1, and most other telephones have a REN of 1 unless marked otherwise. The number dials automatically. 4. Guarantee and service The Binatone Lyris 110 is guaranteed for 12 months from the date of purchase shown on your sales receipt. [. . . ] a cheque or postal order for the value of the repair charge. Return your Lyris 110 to the address given by the Service Department. complies with the essential protection requirements of R&TTE Directive 1999/5/EC on the approximation of the laws of the Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC) and the European Community Directive 2006/95/EC relating to Electrical Safety. Assessment of compliance of the product with the requirements relating to the essential requirements according to Article 3 R&TTE was based on Annex III of the Directive 1999/5/EC and the following standard: EMC: EN55022:2006 EN55024:1998 + A1+A2 Electrical Safety: EN 60950-1:2006 The product is labelled with the European Approval Marking CE as show. Any Unauthorized modification of the product voids this Declaration. [. . . ]