User manual BIOSTAR M7NCD ULTRA

[. . . ] M7NCD Ulltra M7NCD U tra FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. [. . . ] Es ist wichtig, die Anweisung zu folgen. 20 Prozeß zum Löschen des CMOS: 1. Lassen Sie Pin 2-3 von JCOMS1 geshclossen sein. Lassen Sie Pin 1-2 von JCOMS1 geshclossen sein. Schließen Sie den AC-Netzstecker an. Zurücksetzen Sie das Kennwort nach ihrem Wille oder löschen Sie die CMOS-Daten. Anschluss für Gehäuse-Öffnen: JC1 Pin 1 Belegung Gehäuse Öffnen Signal Masse 1 2 JC1 CD-ROM Audio-In Header: JCDIN1 Pin Belegung Link-Kanal Eingabe Masse Masse Recht-Kanal Eingabe 1 JCDIN1 1 2 3 4 Front Panel Audio Header: JF_AUDIO1 9 10 Pin 1 3 5 7 Belegung Mikrofon-Eingang Mikrofon-Betriebsspannung Recht Line-Out Reserviert 1 2 Pin 2 4 6 8 10 Belegung Masse Audio-Spannung Recht Line-Out Schlüsse Link Line-Out JF_AUDIO1 9 Link Line-Out *Reserviert: Nicht in Gebrauch Pin 1 2 J_SPDIF1 3 Digital Audio Anschluss: J_SPDIF1 1 Belegung +5V SPDIF_Ausgang Masse 21 System Operation Modus: JCLK3 JCLK3 Assignment Benutzer Modus (default) (133/ 166 MHz) 1 Pin 1-2 Geöffnet 1 Sicherheit Modus (100 MHz) Pin 1-2 Geschlossen Anmerkung: Wenn "Überspanng Funktion" nicht gelungen ist folgen Sie bitte die Instruktion darunter: 1. Bitte vausschalton Sie den AC-Notzstecker. Lassen Sie Pin 1-2 von JCLK3 geschlossen sein. Schließen Sie den AC-Notzstecker an. Betreten Sie "CMOS Setup Menü" und wählen sie Default-Setting. Ausschalten Sie den AC-Netzstecker wieder. Lassen Sie Pin 1-2 von JCLK3 geöffnet sein. Schließen Sie den AC-Netzstecker wieder. Anschlüsse für die Rückwand 22 Watchdog Technology It is important to know that when overclocking, the system can be at a vulnerable state. Therefore, the BIOSTAR Watchdog Technology was designed to protect your PC under dangerous over-clock situations. Any over-clocking that reaches the threshold settings, the Watchdog Technology will disable your system from rebooting in the BIOS setting. Under this circumstance, please power off your PC. After that, press <Insert> and power on your system simultaneously to restart your system. This user-friendly design can save you from squandering your time on opening the case just to clear the CMOS. In the end, thanks to the Watchdog Technology, everything is back at a safe and sound! 23 StudioFun!is a media-player based on optimized GNU/Linux distribution. It plays DVD, VCD, MP3, Audio CD and various other known file formats. You can take snapshots of video and customize the saved images as screensavers. You can also store the images on USB mass storage devices like flash disks and USB floppy disks. Hardware Requirements The supported hardware list of StudioFun! [. . . ] snaps into place. PROBABLE SOLUTION System does not boot from hard disk drive, can * Check cable running from disk to disk controller be booted from CD-ROM drive. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup. * Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. PROBABLE SOLUTION System only boots from CD-ROM. [. . . ]