User manual BIOSTAR P4M800 PRO-M7 BIOS SETUP

[. . . ] P4M800 Pro-M7 BIOS SETUP BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 2 3 4 5 6 7 8 9 Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Standard CMOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Advanced BIOS Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Advanced Chipset Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Integrated Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Power Management Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 PnP/PCI Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 PC Health Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Frequency/ Voltage Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 i P4M800 Pro-M7 BIOS SETUP BIOS Setup Introduction This manual discussed P hoenix-AwardTM Setup program built into the ROM BIOS. [. . . ] OnChip IDE Channel 0/1 The motherboard chipset contains a P CI IDE interface with support for two IDE channels. Select " Enabled" to activate the first and/or second IDE interface. Select " Disabled" to deactivate an interface if you are going to install a primary and/or secondary add-in IDE interface. The Choices: Enabled (default), Disabled. IDE Pref etch Mode The " onboard" IDE drive interface supports IDE prefetching for faster drive access. If the interface does not support prefetching, or if you install a primary and/or secondary add-in IDE interface, set this option to " Disabled". The Choices: Enabled (default), Disabled. 23 P4M800 Pro-M7 BIOS SETUP Primary / Secondary /Master / Slave PIO The IDE P IO (P rogrammed Input / Output) fields let you set a P IO mode (0-4) for each of the IDE devices that the onboard IDE interface supports. Modes 0 to 4 will increase performance progressively. In Auto mode, the system automatically determines the best mode for each device. The Choices: Auto (default), Mode0, Mode1, Mode2, Mode3, Mode4. Primary / Secondary /Master / Slave UDMA Ultra DMA/100 functionality can be implemented if it is supported by the IDE hard drives in your system. As well, your operating environment requires a DMA driver (Windows 95 OSR2 or a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/100, select Auto to enable BIOS support. IDE HDD B lock Mode Block mode is also called block transfer, multiple commands, or multiple sector read / write. If your IDE hard drive supports block mode ( most new drives do), select Enabled for automatic detection of the optimal number of block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read / write per sector where the drive can support. The Choices: Enabled (default), Disabled. 24 P4M800 Pro-M7 BIOS SETUP VIA OnChip PCI Device If you highlight the literal " Press Enter" next to the " VIA OnChip P CI Device" label and then press the enter key, it will take you a submenu with the following options: Figure 5. 2: VIA OnChip PCI Device VIA-3058 AC97 Audio This option allows you to control the onboard AC97 audio. VIA-3068 MC97 Modem This option allows you to control the onboard MC97 modem. VIA-3043 OnChip LAN This option allows you to control the onboard VIA-3043 OnChip LAN. The Choices: Enabled (default), Disabled Onboard Lan B oot ROM Decide whether to invoke the boot ROM of the onboard LAN chip. The Choices: Disable (default), Enabled. 25 P4M800 Pro-M7 BIOS SETUP OnChip USB Controller This option should be enabled if your system has a USB installed on the system board. You will need to disable this feature if you add a higher performance controller. The Choices: All Enabled (default), All Disabled, 1&2 USB P ort, 2&3 USB Port, 1&3 USB P ort, 1 USB P ort, 2 USB P ort, 3 USB P ort. [. . . ] Disabled (default) Disables the function. Enabled Enables the function. Assign IRQ For VGA This item allows the users to choose which IRQ to assign for the VGA. The Choices: Enabled (default), Disabled. Assign IRQ For USB This item allows the users to choose which IRQ to assign for the USB. The Choices: Enabled (default), Disabled. 36 P4M800 Pro-M7 BIOS SETUP 8 PC Health Status Figure 8: PC Health Status CPU SMART FAN Control by Choose " smart" to reduce the noise caused by CP U FAN. [. . . ]