User manual BISSELL 76X6

[. . . ] TM 76X6/94Z2 SERIES 220-240v USER'S GUIDE 3 Safety Instructions 4 Product view 5-6 Assembly 6-9 Operations 10-15 Maintenance and Care 16-17 Troubleshooting 18 Consumer Services 19 Additional Accessories 19 Replacement Parts 20 Warranty Thank you for buying a BISSELL Multi Cyclonic vacuum We're glad you purchased a BISSELL vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. By purchasing this product you are helping BISSELL with our commitment to reducing our impact on the environment through an expanding range of sustainable design efforts. Your carpet cleaner is well made, and we back it with a limited one-year warranty. [. . . ] The length of the strap may be adjusted as required for comfort. nOTICE: certain While vacuuming, carpets and low humidity conditions may generate small static discharges. The discharges are entirely harmless and are not associated in any way with the main power supply. CAUTIOn:the shoulder To reduce the risk of strap coming loose in operation follow these instructions. CAUTIOn: Button Do not press the Release 8 www. bissell. com while using the Carrying Handle to transport the vacuum cleaner. follow the instructions on the following pages to perform these simple maintenance steps. WARnInG: To reduce the risk of electric shock, turn Power Switch Off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks. Tip: For maximum cleaning performance, check and clean or replace all filters as suggested. 4. Allow parts to dry completely before returning them back into the vacuum. Empty dirt container The dirt container needs to be emptied when the dirt reaches the "full" line on the front of the container. 5. Full Line Unlock Lock Position Slide the Lock `n Seal Lever to the "Unlock" Position position. Grasp handle and pull the dirt container straight out to remove from vacuum. Put the dirt container back in the vacuum and slide the lever to the "Lock" position. The dirt container may be washed in warm water with a mild detergent. Make sure it is completely dry before replacing. 10 www. bissell. com Maintenance and care Cleaning the secondary cyclone Unplug the cleaner from electrical outlet. The secondary cyclone can be reached by removing the dirt container, reaching underneath the upper tank and turning the rim of the frame to unlock. The cyclone and screen may be separated for cleaning. Simply pull up on the screen to separate. The upper tank may also be wiped clean with a damp cloth. 1. 2. 3. Cleaning the pre-motor and post-motor filter 1. Unplug the vacuum from electrical outlet. The Pre-Motor Filter protects the motor from dirt particles. It is located in the slide out tray underneath the Dirt Container. If the filter becomes dirty, pull out the tray, lift out the filter and clean. This filter may be hand washed in cold water with mild detergent. Rinse well and air dry thoroughly before replacing. The HEPA Media Post-Motor Filter assists in the filtration process to return clean air to the room. It is located behind the door on the back of the cleaner. If the filter becomes dirty, open the door, remove the filter and replace. The HEPA Media Filter is not washable. 2. Pre-Motor Filter 3. 3. HEPA Media Post-Motor Filter WARnInG: Do not operate cleaner with damp or wet filters or without all filters in place. www. bissell. com 11 Maintenance and care Rotating brush and drive belt maintenance Check your vacuum cleaner's rotating floor brush and drive belt regularly for debris, wear or damage. Debris can wrap around the brush and hamper its ability to effectively clean your carpet. [. . . ] Pull out and re-insert dirt container correctly Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product. Please do not return this product to the store. www. bissell. com 17 BISSELL consumer service In the UK, Australia, New Zealand, the middle east or Africa, call BIssell Consumer services at the numbers below and we will give you the location of a BIssell Authorized service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. If you have questions about your warranty or need replacement parts please contact the numbers below. If your BISSELL product should require service: for UK inquiries: monday - Thursday 9 am -- 5 pm Friday 9 am -- 4 pm BISSELL Homecare (Overseas) Inc. The Boat Yard 105 straight Road old Windsor Berkshire, sl4 2se United Kingdom Telephone: 0844-888-6644 for new Zealand inquiries: monday - Friday 9 am -- 5 pm Parex Industries Ltd. [. . . ]