User manual BISSELL 80Q2

[. . . ] Cleanview USER'S GUIDE 80Q2 SERIES 2 Thank You Safety Instructions Product View Assembly Operations Maintenance and Care Troubleshooting Consumer Services Replacement Parts Warranty 3 4 5 6-8 9-12 13 14 15 16 Thanks for buying a BISSELL Vacuum We're glad you purchased a BISSELL CleanView Multi Cyclonic vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL CleanView Multi Cyclonic canister vacuum is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you'll receive fast, considerate assistance. [. . . ] For full suction power, close the air flow regulator by sliding the regulator forward to the closed position. Variable Suction Control Tip: Use the variable suction power control and the air flow regulator to reduce air flow as needed when using the tools. CAUTION: Before using your vacuum, make sure that the dirt container and all filters (pre-motor and post-motor) are in place. Do not operate your vacuum without the dirt container and filters. www. bissell. ca 1-800-263-2535 7 Operations Special tools Your BISSELL CleanView Multi cyclonic is not only a powerful carpet and rug vacuum cleaner, it's also a versatile bare floor and above floor vacuum cleaner when you select one of the special tools. Floor nozzle: Use to vacuum carpets, rugs and bare floors. Swivel head turns to get into tight spaces and fits under cabinets. To vacuum carpets and rugs, push the brush switch to the carpet position . This will pull the brushes up into the floor nozzle. To vacuum bare floors, push the brush switch to the bare floor position . This will extend the brushes down from the floor nozzle. Upholstery tool: Use the upholstery tool to clean curtains, draperies, cushions and fabrics. Crevice tool: Use the crevice tool in tight, narrow spaces. Dusting brush: Use the dusting brush to dust furniture, blinds, books, lamps, shelves and baseboards. Brush Up 1. 2. Brush Down 8 www. bissell. ca 1-800-263-2535 Maintenance and care Emptying the dirt container Empty the dirt container as soon as the dirt reached the "FULL" lines on the sides of the dirt container. Unplug the vacuum from the electrical outlet. Press the dirt container release button located on the back of the carry handle and lift up to remove. Method #2 is recommended for allergy sufferers. Method #1 ­ Hold the dirt container over a trash can and push the emptying button located on the back bottom of the dirt container to open the bottom. Close the bottom after the dirt empties and make sure it clicks back into the locked position. Method #2 ­ Place a plastic bag over the bottom of the dirt container. Push the emptying button, located on the back bottom of the dirt container, through the plastic to open the bottom. After the dust settles, remove the plastic bag to discard. Close the bottom and make Emptying sure it clicks back into the locked Button position. WARNING: To reduce the risk of electric shock, turn power switch OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks. Dirt Container Release Button www. bissell. ca 1-800-263-2535 9 Maintenance and care Cleaning the inner cyclone & screen Filters protect the motor from dirt and dust particles. Use only BISSELL replacement filters in your CleanView Multi Cyclonic 1. [. . . ] Vacuuming of dust from products like plaster, concrete or ashes will damage the motor and void the warranty. 4. 4. Pre-Motor Filter Filter Tray Tip: For maximum cleaning performance, check the filters often and clean or replace if necessary. WARNING: Do not operate cleaner with damp or wet filters or without all filters in place. www. bissell. ca 1-800-263-2535 11 Maintenance and care Cleaning the Post-motor HEPA media filter The post-motor HEPA media filter assists in the filtration process to return clean air to the room. Use only BISSELL replacement filters in your CleanView Multi Cyclonic. Checkandcleanorreplacepre-motorandpost-motorfilters 4. Makesurehoseconnectorislockedintosuctionopening 6. [. . . ]