User manual BLACK & DECKER GK43

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BLACK & DECKER GK43. We hope that this BLACK & DECKER GK43 user guide will be useful to you.

Lastmanuals help download the user guide BLACK & DECKER GK43.


BLACK & DECKER GK43 : Download the complete user guide (5997 Ko)

Manual abstract: user guide BLACK & DECKER GK43

Detailed instructions for use are in the User's Guide.

[. . . ] 2 3 4 (Original instructions) Intended use Your Black & Decker chainsaw has been designed for pruning and felling trees and cutting logs. ENGLISH Safety instructions General power tool safety warnings @ Warning!Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool. [. . . ] Note: When the chain is new, check the tension frequently (after disconnecting from the mains) during the first 2 hours of use because a new chain stretches slightly. Tension the chain using the chain tension adjusting screw (5), turn clockwise to tighten. Set the front guard/chain brake assembly to the forward position (fig. U Place the chain (6) over the guide bar (7) making sure that the saw chain cutters on the upper part of the guide bar (7) face towards the front (fig. U Guide the chain (6) around the guide bar (7) and pull it to create a loop to one side at the rear end of the guide bar (7). Make sure that the sliding nut peg (14) locates into the tensioning hole (15) (fig. F) u Remove the oil cap (3) and fill the reservoir with the recommended chain oil. U Periodically switch off and check the oil level indicator (11); if it is less than a quarter full, disconnect your chainsaw from the mains supply and refill with the correct oil. Make sure that the front guard/chain brake assembly (4) is in the set (forward) position before refitting (fig. Turn the chain adjust locking knob (9) to attach the chain cover assembly (10) but do not tighten fully. U Turn the chain tension adjust screw (5) clockwise until the chain (6) is tight. U u Note: It will not be possible to switch the tool on if the front guard/chain brake assembly is not in the "set" position. Push the lock-off button (2) and then push the on/off switch (1) to start. U When the motor starts, remove your thumb from the lock button (2) and grip the handle firmly. It will do a better and safer job at the speed for which it is designed. U Pull the front guard/chain brake assembly (4) back into the "set" (fig. How the anti-kickback chain brake works In the event of kickback, your left hand comes in contact with the front guard, pushing it forwards, toward the workpiece, and stops the tool within a few fractions of a second. G) Before use and after every 10 minutes of use, you must check the chain tension. The tension is correct when the chain (6) snaps back after being pulled 3 mm away from the guide bar (7). There should be no "sag" between the guide bar (7) and the chain (6) on the underside. 9 ENGLISH (Original instructions) Do not attempt to fell trees where the tree diameter is greater than the cutting length of the chainsaw. U Make a horizontal cut to a depth of between 1/5th and 1/3rd of the diameter of the tree, perpendicular to the line of fall at the base of the tree (fig. [. . . ] For dette anbefaler vi at du kjøper Black & Deckers skjerpesett for kjedesager (fås hos autoriserte Black & Deckerserviceverksteder og utvalgte forhandlere). Det kan være lokale bestemmelser for separat avfallshåndtering for elektriske produkter fra husstander på kommunale avfallsplasser eller hos forhandleren, når du kjøper et nytt produkt. , Utrechtseweg 310, 6802 ED Arnhem, The Netherlands ID-nummer for varslet organ: 0344 Nivået for akustisk effekt er i samsvar med 2000/14/EF (artikkel 13, vedlegg III): LWA (målt lydeffekt) 104 dB(A) LWA (garantert lydeffekt) 107 dB(A) Disse produktene er også i samsvar med direktivet 2004/108/ EF & 2011/65/EU. Hvis et Black & Decker-produkt går i stykker på grunn av material- og/eller fabrikasjonsfeil eller har mangler i forhold til spesifikasjonene innen 24 måneder fra kjøpet, påtar Black & Decker seg å skifte ut defekte deler, reparere produkter som har vært utsatt for alminnelig slitasje, eller bytte ut slike produkter med minst mulig vanskelighet for kunden, med mindre: u Produktet har vært brukt i yrkes-/næringsvirksomhet eller til utleie. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLACK & DECKER GK43

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BLACK & DECKER GK43 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag