User manual BLAUPUNKT AUSTIN CR45

[. . . ] However, there is no guarantee that radio interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Precautions · Avoid installing the unit where it would be subject to high temperatures, such as in direct sunlight or a hot air stream from the heater, or where it would be subject to dust, dirt, or excessive vibration. · Do not turn on the unit if the temperature inside the car is very high. [. . . ] Following four messages (factory set) can be edit with 8 characters each. Turn-on message · MESSAGE 1 : · MESSAGE 2 : Turn-off message · MESSAGE 3 : · MESSAGE 4 : Erasing the turn on/off message You can erase the turn on/off message if so desired. Playing the CD player Loading Discs 1. 2. Repeatedly press the DISP to display the MESSAGE, then rotate the dial to select the message you want to erase. Press the Press the MUTE / SENS . 1. 2. Press the OPEN and insert the disc. HELLO WELCOME SEE YOU GOOD-BYE The message flashing. Close the front panel. `` LOADING '' indicator will flash in the display window. 3. 4. DISP for more than 2 seconds. Note Make sure that the front panel is closed when playback begins. . Repeat steps 1. To return to the normal radio reception, Press DISP Repeatedly press the DISP to display the " MESSAGE " on the display window. Rotate the dial to select the desired message you want to edit. MESSAGE1 MESSAGE2 MESSAGE3 MESSAGE4 2. Demonstration mode The unit shows a demonstration of each function. When a demonstration is finished, it begins again after 10 seconds, and this is repeated. Playback with the front panel open causes the unit to turn off automatically in about 10 minutes. Labeled side up 3. Press the MUTE / SENS , then enter the character. A. Press the SC/PS again to cancel this feature. Stopping Playback Press the FT or AM, AT). BND / TS to select the radio reception (FM I, FM II, FRANÇAIS Disc Select Press the Disc select buttons to select the desired disc for play. + /2 Ejecting Discs Press the panel. to eject the disc located behind flip-down front Repeat Play Press the 5/RPT during CD mode. The `` RPT ON'' indicator appears in the display window and the current track is played repeatedly. Press the 5/RPT again to cancel this feature. : To advance to a higher number disc. : To return to a lower number disc. - /1 Notes · The unit will turn on automatically when a CD is inserted if the ignition switch is ``ON''. · When the disc is ejected from the CD slot, remove it within 10 seconds; otherwise, the disc will be reloaded automatically. Mix Play Press the 4/MIX during CD mode. The `` MIX ON'' indicator appears in the display window. All the tracks on the current disc are played in random order. Press the 4/MIX again to cancel this feature. Track Search TUN/ TRK Press the . Track numbers appear in the display window. ESPAÑOL : Playback starts from the beginning of the next track. : Playback starts from the beginning of the current track. [. . . ] Insert the " TOP R ''and " TOP L ''of the release keys on the right and left position until it clicks respectively, to remove the unit. Back of the unit Warning Cleaning the Connectors If the connectors of the unit and the front panel are contaminated, malfunctions may occur. Detach the front panel and clean the connectors with an alcohol dampened cotton swab as shown below. As shown in the figure below, push the plate spring firmly to remove the release keys. Main unit Back of the front panel Notes · Handle the release keys carefully to avoid injuring your fingers. · Keep the release keys in a safe place for future use. Returning to the Initial Settings When the reset button is pressed, the microcomputer of the unit returns to the initial settings. If the display window is not properly shown or the unit malfunctions, press the reset button with the point of a sharp object such as a ball-point pen. Reset button PORTUGUÊS ESPAÑOL FRANÇAIS Use only a fuse with the specified amperage (10 A). [. . . ]