User manual BLAUPUNKT BURNING DESIRE II

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BLAUPUNKT BURNING DESIRE II. We hope that this BLAUPUNKT BURNING DESIRE II user guide will be useful to you.

Lastmanuals help download the user guide BLAUPUNKT BURNING DESIRE II.


BLAUPUNKT BURNING DESIRE II : Download the complete user guide (286 Ko)

You may also download the following manuals related to this product:

   BLAUPUNKT BURNING DESIRE II annexe 1 (273 ko)

Manual abstract: user guide BLAUPUNKT BURNING DESIRE II

Detailed instructions for use are in the User's Guide.

[. . . ] The cross section of the positive and negative cables must be at least 25 mm2. The positive cable between the battery and the amplifier must be protected directly at the battery using a fuse holder (100 A). The positive cable must be protected directly at the amplifier using the fuse holder that is included (4 x 80 A). Note: You must make sure that the fuse holder is protected effectively against moisture. [. . . ] De or ask for them directly at: Blaupunkt GmbH Hotline Robert-Bosch-Str. 200 D-31139 Hildesheim You can also obtain further information on our Velocity series on the Internet at http://www. Note: In the case of longer supply lines to the vehicle battery, a second battery can be installed alongside the amplifier in order to stabilise the voltage. The amplifier is suitable for connection to car audio systems that are equipped with RCA connections. If you want to connect it to car audio systems that are equipped with an ISO connection, please use the Blaupunkt ISO-RCA adapter. Usage options and loudspeaker connection: Burning Desire II Max power 4 ohms Max power 2 ohms Max Power 1 ohm RMS power 4 ohms RMS power 2 ohms RMS power 1 ohm Frequency response Total harmonic distorsion Input impedance Signal-to-noise ratio Input sensitivity Low pass filter Bass boost Subsonic filter Dimensions WxHxD (mm), . preamp OUTPUT Outputs for connecting a second amplifier (formation of chains of amplifiers). 7) Before installation, adjust the position of the CONFIG switch on the power amplifier in order to set the frequency coverage of the signal that is sent to the loudspeakers and the RCA output jacks. LP/LP position: In this switch position, the bass range that is limited by the crossover frequency control (LP FREQ) is sent to the subwoofer as well as to the RCA OUTPUT. FLAT/FLAT position: In this switch position, the frequency coverage up to 450 Hz is used for the loudspeaker, and the frequency coverage that is predetermined by the car radio is used for the RCA OUTPUT. Note: The SUBSONIC filter and BASS BOOST control do not have any function in this position. Crossover frequency control (LP FREQ) If the crossover is activated (LP/FLAT or LP/LP) by adjusting the position of the CONFIG switch, you can then use the LP-FREQ control to adjust the crossover frequency of the filter anywhere between 40 Hz and 300 Hz. Settings for a subwoofer In order to obtain the best sound when a subwoofer is connected, the subwoofer must only be fed with low frequencies, i. Firstly, turn down the GAIN control on the Burning Desire II to minimum and set the LP-FREQ control to its centre position. Now play some music on your car sound system that you are very familiar with and that contains some low bass (e. Now slowly increase the volume of the subwoofer by turning the GAIN control on the subwoofer amplifier in a clockwise direction until you feel that the sound of the music is well balanced, i. Now listen to the relationship between deep male voices and the higher bass frequencies and also take note of the relationship between the upper bass (kick bass) and the lower bass. The bass should ideally sound crisp and have a clear low bass component, and male voices should neither sound too weak nor should they billow out. [. . . ] Note: You must make sure that the fuse holder is protected effectively against moisture. Note: In the case of longer supply lines to the vehicle battery, a second battery can be installed alongside the amplifier in order to stabilise the voltage. Securely screw a standard 25 mm2 negative cable to an interference-free ground connection point (bolt connected to the car body, car body sheet metal) - though do not connect it to the negative terminal of the battery. Scratch the surface down to the bare metal at the point at which the ground contact is made and apply graphite grease. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLAUPUNKT BURNING DESIRE II

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BLAUPUNKT BURNING DESIRE II will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag