User manual BLAUPUNKT CD 2001

[. . . ] HIGH POWE R 180 S WATT CD PWR FM TS 01 CD 20 LD MIX RPT DISP /SENS AM VOL AUD Robert Bosch Corporation Sales Group -- Blaupunkt Division 2800 South 25th Avenue, Broadview, Illinois 60155 PORTUGUÊS ESPAÑOL FRANÇAIS High-Power FM/AM/CD Receiver with Detachable Face Autoradio AM/FM à Lecteur CD de Forte Puissance et à Face Amovible Receptor FM/AM/Reproductor de CD de Alta Potencia y con Panel Extraíble Rádio FM/AM/CD de Alta Potência com Face Removível ENGLISH CD 2001 N/T TU RK FCC WARNING This equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation. [. . . ] The unit will stop at each preset station for 8 seconds, before continuing to the next preset station. again to stop Preset Scan Tuning and rePress the main this on the selected frequency. 1. 2. Press the Press the AM 1 or 6/ FM to select the desired radio band. momentarily. Local/Distant (LO/DX) Selection This feature is used to select the strength of the signals at which the radio will stop during Seek Tuning. Press the LD/SENS for more than 2 seconds to select the Local setting and only the strongest (local) stations will be received. The "lo" indicator appears in the display window. Pressing again for 2 seconds will select the Distant setting and the radio will stop at a wider range of signals, including weaker more distant stations. The "lo" indicator will go out on the display window. The "Distant" setting is the recommended default mode of reception. Manual Tuning 1. 2. Press the AM Memorizing Stations Automatically (Travel Store) FM or to select the desired band. Press the or and hold for more than 0. 5 second to activate the manual tuning mode. After 4 seconds duration of completing Manual Tuning, the tuning control will revert to the Seek Tuning mode. 1. 2. Press the AM or FM to select the desired band. Hold the AM or FM pressed for longer than 2 seconds. Up to 6 stations with strong signals will be automatically stored in preset memory for the selected band. Note This function is available for FM III and AM II. Scan Tuning 1. 2. Press the AM or FM to select the desired radio band. Memorizing Only the Desired Stations A total of 30 stations (18 for the FM I, FM II and FM III, 12 for AM I and AM II) can be stored in preset memory. Press the . The unit will scan the selected radio band for stations. Press the again to stop Scan Tuning and remain on this selected frequency. Tips When tuned in to broadcasting stations, the antenna indicator on the display window is lit. 1. 3. Press the Press the AM or or FM to select the desired radio band. to tune in stations. Press and hold the desired preset memory button 1 6/ for about 2 seconds until the frequency indicator flashes twice. The number of the pressed preset memory button appears on the display window. Note If/when you store another station on the same preset number button, the previously stored station is replaced with new one. E-4 CD Operations Playing the CD player Loading Discs Insert the disc into the CD insertion slot with the labeled side facing up. '' indicator will light up in the display window and play`` back begins automatically. Labeled side up Listening to a disc that is already loaded Press the CD to select the CD mode. Playback begins automatically. Scan Play ENGLISH Press the during CD mode. The ``SCAN'' indicator appears in the display window. [. . . ] Use of another type of fuse can result in a fire or unit damage. · Handle the release keys carefully to avoid injuring your fingers. · Keep the release keys in a safe place for future use. Cleaning the Connectors If the connectors of the unit and the front panel are contaminated, malfunctions may occur. Detach the front panel and clean the connectors with an alcohol dampened cotton swab as shown below. Main unit Back of the front panel Returning to the Initial Settings When the reset button is pressed, the microcomputer of the unit returns to the initial settings. [. . . ]