User manual BLAUPUNKT CHICAGO IVDM-7002 EU

[. . . ] If the instructions given here do not describe your fitting process, please contact your Blaupunkt dealer, your vehicle manufacturer, or use our telephone hotline. · The Chicago IVDM-7002 is suitable for vehicles with: - 11 V - 14. 4 V battery voltage - the negative terminal connected to the chassis ENGLISH 7 Contents Safety information . . . . . . . . . . . . . . . . 7 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] We accept no liability for incorrect connection or its consequences!1 Handbrake (green) Connection for the handbrake signal. 2 Ignition positive (blue) Additional positive ignition output. 3 Navigation mute (orange) Control line for muting the audio source during a navigation announcement. 4 Ignition positive (brown/white) Additional positive ignition output 5 Centre loudspeaker + (black) 6 Centre loudspeaker - (black/ green) Additional loudspeaker fitted in the centre of the instrument panel. 7 Ignition positive amplifier (blue/ white) Positive ignition output for a connected amplifier 8 Reversing light connection The cable end is included in the vehicle-specific adapter cable, and must inserted into chamber A, pin 3, if necessary. 1. 3 Centre loudspeaker The centre loudspeaker is connected through the two black leads 5 and 6 (see Fig. Your dealer can tell you about available centre loudspeakers. 1. 1 Power and loudspeaker connections The device must be connected to your vehicle using the enclosed connection cable (8 619 002 597) and an adapter cable specific for your vehicle (see Fig. Note: An adapter cable specific for the vehicle must also be used even if the vehicle is already fitted with ISO connectors. 1. 4 Connect the handbrake signal Install a cable from the handbrake switch to the connection on the control unit 1 (see Fig. Ensure that the connection is earthed when the handbrake is on. 1. 5 Ignition positive for amplifier Take a cable from the connection 7 to the positive ignition connection of the amplifier (or amplifiers) (see Fig. 1). 1. 2 Additional free connections The connecting leads described below must, if necessary, be separately connected to the corresponding connections on the vehicle (see Fig. 1). 1. 6 RC 10 connection (accessories) The receiver sensor for the optional remote control RC 10 is connected to the monitor unit through the enclosed adapter 8 619 002 421 (see Fig. Installation 2. 1 Radio antenna In ready-fitted vehicles (e. g. VW, Seat, Audi) the antenna supply voltage is provided through the antenna cable (see the vehicle's user instructions). You can obtain an antenna supply junction piece (order no. 7 691 290 202) or the adapter cable (order no. Fitting and connecting the cable are described in the antenna fitting instructions. 10 2. 3 Fitting the bracket The bracket included with the Chicago IVDM-7002 allows it to be mounted in vehicles with a DIN car radio slot with dimensions of 182 x 53 x 180 mm and with instrument panels that are between 1 and 20 mm thick in the region of the securing tabs (see Fig. To mount the device you must push the bracket into the opening and check which of the bracket's securing tabs can be bent over with a screwdriver (see Fig. Note: Bend all the securing tabs if possible. 2. 5 Removing the monitor unit Remove the plastic masking frame. [. . . ] Join the adapter cable's free lead to the navigation mute lead 3 of the adapter cable 8 619 002 597 (see Fig. Connection diagrams Power connection on vehicle-specific connector . . . . . . . Connection of the connecting cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fitting the Chicago IVDM-7002 . . . . . . . . . . . . . . . . [. . . ]