User manual BLAUPUNKT GTB 100 BP11 INSTALLATION

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BLAUPUNKT GTB 100 BP11. We hope that this BLAUPUNKT GTB 100 BP11 user guide will be useful to you.

Lastmanuals help download the user guide BLAUPUNKT GTB 100 BP11.


BLAUPUNKT GTB 100 BP11 INSTALLATION: Download the complete user guide (1380 Ko)

Manual abstract: user guide BLAUPUNKT GTB 100 BP11INSTALLATION

Detailed instructions for use are in the User's Guide.

[. . . ] For devices purchased outside the European Union, the warranty terms issued by our respective responsible domestic agency are valid. Please observe the following safety notes during the installation and connection. ­ When you drill holes, ensure that you do not damage any vehicle components. ­ An incorrect installation can result in malfunctions of the electronic vehicle systems or your car sound system. [. . . ] In conclusion, allow us a few words about the topic of health protection: During the playback of music in your vehicle, please consider that continuous sound-pressure levels above 100 dB can lead to permanent damages to the human ear and even to loss of hearing. Using today's high-performance systems and loudspeaker configurations allows for reaching soundpressure levels above 130 dB. Please observe the following safety notes during the installation and connection. ­ When you drill holes, ensure that you do not damage any vehicle components. ­ The cross section of the plus and minus cable may not be less than 6 mm2. ­ An incorrect installation can result in malfunctions of the electronic vehicle systems or your car sound system. You can select between 2 different audio inputs; ­ Cinch (RCA) ­ Hi level (loudspeaker connections) Use only one of the audio inputs; otherwise, it may lead to audio interferences. The preamplifier outputs are connected to the cinch (RCA) sockets 1 via a shielded sound cable. with control via the loudspeaker outputs , the input connections of pos. 2/3 are fed to the closest loudspeaker cables (front or rear) on the left and right. Bridge output stages (BTL) can also be connected directly without an additional adapter. With respect to accident safety, the GTA 250 BP11 must be secured in a professional way. When selecting the installation location, select a dry location that offers sufficient air circulation for cooling the amplifier. The GTA 250 BP11 must not be installed on rear shelves, rear seats or other locations that are open to the front. The installation location must be suitable to accept the accompanying screws and provide a firm support. ­ Securely fasten commercially available minus cables to a noise-free earth point (chassis screw, chassis metal) (not to the minus pole of the battery). ­ Scrap the contact surfaces of the earth point until they are bright and grease with graphite grease. This allows the amplifier to be used for one or several subwoofers or mid-range drivers. In this configuration, the amplifier combines the right and left channel to a singlechannel output (mono output). Note: The amplifier can add the right and left signal information only if the right as well as the left RCA connection were carried out. Caution: In a bridge circuit, the amplifier load must be 4 ohm or higher. A lower load leads to an overheating or switch-off of the amplifier and can cause permanent damages. [. . . ] The fuses integrated in the amplifier (Fuse) protect the power amplifier and the entire electrical system in case of an error. If a replacement fuse is used, never bridge fuses or replace them with a type with higher current. This allows the amplifier to be switched on and off using the on/off-switch of the radio device. The Level control is used to adjust the input sensitivity of the power amplifier to the output voltage of your car sound system preamplifier output. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLAUPUNKT GTB 100 BP11

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BLAUPUNKT GTB 100 BP11 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag