User manual BLAUPUNKT HEIDLEBERG CD51

[. . . ] Radio / CD Heidelberg CD51 Operating instructions 1 2 3 4 16 15 5 6 14 7 13 12 11 10 8 9 3 PORTUGUÊS ESPAÑOL FRANÇAIS ENGLISH CONTROLS 1 2 3 4 button - unlatches the flip/release panel Volume control Button - switches the radio and mute function on/off RDS button - switches RDS convenience function on/off (radio data system). FM button, selection of FM waveband and FM memory levels TS, starts the Travelstore function. Display (display field) button - indicates the time on the display DIS, change display contents MENU button - selects the menu for basic settings button - opens the flip/release panel Arrow-key block OK button - confirms menu entries and starts the scan function < = DEQ button (digital equalizer) switches the equalizer on/off AUD button (Audio) - adjusts bass and treble, balance and fader LD - switches loudness function on/off Key block 1 - 6 AM button, selection of AM waveband CD·C button - selects between CD, CD changer and AUX sources (if connected) > ?@ 5 6 7 8 9 : ; 4 TABLE OF CONTENTS Road safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] "0" means the beep is off, "9" means maximum beep volume. Selecting the waveband/ memory This unit can receive programmes broadcast over the FM as well as AM wavebands. There are three preset memory levels for the FM range and one for the AM range. The stations are stored in the FMT memory. Note: Stations that were previously stored in this memory are deleted in the process. Ending SCAN, continuing to listen to a station Press the OK button ;. The scanning process is completed, the station last scanned remains active. Setting the scanning time Press the MENU button 8. Press the button : repeatedly until "SCANTIME" appears on the display. Hold down the FM / TS button 5 for more than two seconds. The automatic station-storing procedure begins. "TRAVEL-STORE" appears on the display. Once the process is completed, the station stored in FMT memory location 1 is played. Use the buttons : to set the desired scanning time. Once the setting has been completed, press the MENU button 8 or OK ;. Note: The set scanning time also applies to scanning in the CD and CD changer mode. Listening to preset stations Select the memory or frequency range. Hold down the preset station button 1 - 6 > of the desired station. Optimising radio reception High-frequency cut-off feature (HICUT) The HiCut function improves the sound during poor radio reception (only FM). If interference occurs, the treble is automatically reduced and thus also the interference level. Switching HiCut on/off Scanning receivable stations (SCAN) You can briefly listen in to all receivable stations. The scanning time can be set in the menu at between 5 and 30 seconds. Starting SCAN Hold down the OK button ; for more than two seconds. "SCAN" appears briefly on the display, followed by the current station name or frequency, which flash. Press the MENU button 8. Press the button : repeatedly until "HICUT" appears on the display. Use the HICUT. or button : to select 12 RADIO MODE "HICUT 0" denotes no treble reduction, "HICUT 3" the greatest automatic reduction of the treble and the interference level. "radio texts", hold down the RDS button 4 until "NAME VAR" appears on the display. ENGLISH PORTUGUÊS ESPAÑOL FRANÇAIS In order to reactivate the display of Press the MENU button 8 or OK ;. Interference-related waveband change (SHARX) With the SHARX function you can eliminate interference from neighbouring stations almost completely (FM). Activate the SHARX function in an area of high transmitter density. Switching SHARX on/off Setting the display In radio mode you can choose between the continuous display of the time or the continuous display of the station name/ frequency. Hold down the / DIS button 7 for more than two seconds until the desired feature appears on the display. Changing the tuner This unit is fitted with a multiband tuner. The tuner can be adjusted to meet the specific demands of the various states. The regions available are: America, Europe, Asia and Thailand. [. . . ] Select "DIGITAL EQ" using the or button :. or Press the MENU button 8. "MENU" appears on the display. Select the filter using the button :. Press the Press the or button :. To select the frequency, press the button :. button : repeatedly until "EQ DISPLAY" appears on the display. Press the Set the level using the ton :. or but- To select the next filter, first press the OK button ;, then the button :. or or button : to choose between displaying "SPECTRUM1" and "SPECTRUM2" or "EQ DISP OFF" set the volume distribution left/right. [. . . ]