User manual BLAUPUNKT MPA 2

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BLAUPUNKT MPA 2. We hope that this BLAUPUNKT MPA 2 user guide will be useful to you.

Lastmanuals help download the user guide BLAUPUNKT MPA 2.


Mode d'emploi BLAUPUNKT MPA 2
Download

You may also download the following manuals related to this product:

   BLAUPUNKT MPA 2 annexe 1 (271 ko)

Manual abstract: user guide BLAUPUNKT MPA 2

Detailed instructions for use are in the User's Guide.

[. . . ] Disconnect the negative terminal of the battery before carrying out installation and connection work. Observe the vehicle manufacturer's safety instructions (regarding airbags, alarm systems, trip computers, vehicle immobilisers). The final stage must be installed professionally for reasons of safety. [. . . ] High-level inputs The amplifier is equipped with high-level inputs to permit connection to radios without preamp outputs (Fig. This enables direct connection to be made to the radio's loudspeaker output. Gain control The gain control enables the input sensitivity of the final stage to be matched to the output voltage of your car radio preamp output. Adjust the input sensitivity in accordance with the manufacturer's specifications when connecting the amplifier to other radios. important: Turning the gain control clockwise increases the input sensitivity of the amplifier , and thereby also the volume. The gain control is however not a volume control; an increase in volume is not achieved in the maximum position, even if this subjectively appears to be the case. The system merely increases the volume more quickly when the volume is turned up on the radio. Tri-mode loudspeaker connections MPA amplifiers can be used in a combined mono/stereo mode (Fig. This facility enables the amplifier to be used simultaneously with stereo satellite speakers (mid-range and tweeter) and a mono subwoofer. The connections are somewhat more complicated in this case, as they require the use of passive crossover networks (not supplied with the amplifier) which divide the frequency ranges between the various loudspeakers. The requisite connections can be taken from the diagrams below. If you do not wish to purchase and connect the components separately, a number of ready-assembled tri-mode crossover networks are available. ask your local car audio retail store for details. CAUTION: In tri-mode (combined mono/stereo mode) the amplifier must be presented with a load of at least 2 Ohms (stereo satellite speakers) or 4 Ohms (mono subwoofers). Lower loads cause overheating of the amplifier and may damage it permanently. loudspeaker connections (If the amplifier is to be connected in a bridged mode , proceed with the section "Bridged loudspeaker connections". ) As with any audio component, connection of the amplifier and speakers with the correct polarity is essential for good bass reproduction. This enables you to use the amplifier for one or more subwoofer(s) or a mid-range speaker. [. . . ] Note: If the amplifier is to be used in the tri-mode configuration, the crossover frequency selector switch must be set to , , Flat" in order to make the full frequency range available. adjustment of the type and range of the cross-over frequencies. MPA 2 The MPA 2 has a special subwoofer crossover frequency which can be selected between 75 Hz and 100 Hz. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLAUPUNKT MPA 2

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BLAUPUNKT MPA 2 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag