User manual BLAUPUNKT ODX 693E

[. . . ] 17 Rear of the device . . . . . . . . . . . . . . . . . . . . . . . . . 17 Remote control . . . . . . . . . . . . . . . . . . . . . . 18 Infrared transmitter . . . . . . . . . . . . . . . . . . . . . . . . 18 Infrared receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If installation or maintenance is carried out incorrectly, the vehicle's electronic systems might malfunction. Disconnect the negative terminal of the battery!When doing so, please observe the safety notices provided by the vehicle manufacturer. When drilling holes, always make sure that none of the vehicle's components can be damaged in the process. Depending on the vehicle model, the conditions in your vehicle may differ from the description provided here. We do not accept liability for any damages caused by mistakes made during installation or when making connections or for any consequential damages. If these instructions are not suitable for your particular installation, please contact your Blaupunkt dealer, your vehicle manufacturer or our telephone hotline. Notes and trademarks The information stated herein is subject to change at any time without notice. 16 CONNECTIONS AND CONTROLS Front of the device 1 2 3 4 5 6 7 8 9 Power-on indicator (LED) Connection for remote control Digital input (optical) Digital input (coaxial) Gain control for Hi-Level input Control for input sensitivity at AUX2 Control for input sensitivity at AUX1 Analogue input (AUX2) Analogue input (AUX1) DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Connections and controls : Preamplifier output for front channel left (FL) ; Preamplifier output for surround channel left (SL) < Preamplifier output for centre channel (CEN) = Preamplifier output for front channel right (FR) > Preamplifier output for surround channel right (SR) ?Preamplifier output for subwoofer channel (SUB) =>? Signal Input Power Control Out Optical Coaxial Hi-Level Aux2 Aux1 R Aux2 Aux1 FR Line out SR SUB Input Gain L FL SL CEN 1 2 3 4 5 6789:;< Rear of the device 1 Connection for +/- and remote 2 Fuse (30 A) 3 Loudspeaker connection 4 Connection for Hi-Level input Speaker Out REM Fuse 30A SL SR CEN FL FR FR FL RR RL + Hi-Level In DC 12V In 1 2 3 4 17 REMOTE CONTROL Remote control ODA Surround UP 2 L C R SU B VOL DOWN FT dB 1 SL L S S S S PRO LOGIC SURROUND EQUALIZER 3 OPT IN / COA IN D STATUS LISTEN INPUT SETUP ENTER MUTE POWER BLAUPUNKT Infrared transmitter 1 Display 2 Volume control 3 Selector switch for analogue / digital input 4 Mute switch Battery compartment You must insert the supplied batteries before using the remote control for the first time. Slide open the battery compartment cover in the direction indicated by the arrow, and insert the batteries as shown in the diagram (on the floor of the battery compartment). Infrared receiver A R AUX1 / AUX2 Mute 4 18 REMOTE CONTROL DEUTSCH Display and controls C SL S S dB 5 : ; < STATUS LISTEN INPUT 3 6 2 1 7 MUTE POWER 1 POWER on/off button For the remote control. 2 ENTER button Available when making user-defined changes to the system settings. Press ENTER to confirm your selection. 6. Press ENTER repeatedly to select the 6 individual loudspeaker channels. Now adjust the balance (0 to -20 dB) using the arrow buttons (DOWN or UP ). Press ENTER to confirm your settings. 3. Step: Configuring the EQUALIZER Press SETUP. Press the arrow buttons (UP or DOWN ) to set the equalizer setting to POP / CLASSIC / ROCK or OFF. Press ENTER to confirm your selection. 7. Press ENTER repeatedly to select the required loudspeakers. or Press the arrow buttons (UP DOWN ) to set the delay for the FRONT / CENTER / SURROUND channels (0 to 1800 cm). Note: The CENTER delay time is dependent on the FRONT and SURROUND delay time settings. Step: Switching PRO LOGIC on/off Press SETUP. [. . . ] We do not accept liability for any damages caused by mistakes made during installation or when making connections or for any consequential damages. The amplifier must be secured in a suitable installation location, e. g. beneath the seats or in the car boot (Fig. When choosing an installation location, you should select one which is dry and which provides sufficient air circulation to cool the amplifier. [. . . ]