User manual BLAUPUNKT SHARK LINE A-RNT T01-M

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to contact the dealer or an experienced RadioE!V technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Owner's Record The model and warranty numbers are located on the top of the unit. Record the warranty (serial) number in the space provided below. Refer to these numbers whenever you call upon your Blaupunkt dealer regarding this product. [. . . ] You'll be glad you did! GENERAL RECOMMENDATIONS l l l l If you're not confident that you can install the unit correctly, have it installed by a qualified Blaupunkt installation technician. Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC). Be sure to detach the faceplate before you start to connect or install the unit. We recommend making and testing all electrical connections before installing the unit. Connect the leads (wires) according to instructions and diagram below. ELECTRICAL CONNECTION INSTRUCTIONS Disconnect the vehicle battery's negative terminal before making connections. Connect the speakers and/or external amplifiers (if you have any) following the guidelines in the SPEAKER CONNECTION section below. Connect the blue (trigger output) lead to an amplifier's trigger input terminal and/or antenna motor trigger input terminal (if you have either or both of these items). The combined total amperage required for triggering the antenna motor and/or amplifier must not exceed 300 mA. DO NOT connect the blue lead to the antenna's and/or amplifier's power supply input. Connect the black (power ground) lead to a grounded metal part on the vehide. We recommend grounding all audio system black ground leads (head unit, external amplifier, etc. ) to a common grounding point, preferably a non-painted surface under the instrument panel. This will prevent them from touching the vehicle or each other and causing a short-circuit and damage to the radio or vehicle. Connecting the Pre-Amp Outputs to External Amplifier(s) To prevent short circuits or serious damage o the head unit, amplifier, and/or speakers: l Follow the amplifier's instructions on how to connect the unit's preamp outputs to the amplifier(s) and connect the speaker(s) directly to the amplifier. l l 3. 5mm PORTABLE FUSE (1 OA) RIGHT FRONT SPEAKER LEFT REAR SPEAKER RIGHT REAR SPEAKER Harness has single blue lead that can be used for either antenna motor or amp trigger or spliced for use with both. (See note 3. ) 7 Installation Recommendations l l l l Carefully choose the mounting location so that the unit won't interfere with normal driving. Avoid mounting locations where the unit would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would subject to dust, dirt or excessive vibration. The illustration below shows a typical installation, however, you may need to adjust the installation, depending on the unit. Low-lmpendance (100 L, I) Preamplifier 55 dB 65 dB 0. 10% dB 30-l 8, 000 Hz + 3 dB 180 x 52 x 155 mm, 7 x 3 x 61/s in. 1. 4 kg (3. 0 lb. ) 12 V DC car battery (1 l-16 V DC allowable) 15°F to 12O"F, -10°C to 50°C Unit Faceplate Wire Harness, including e-Channel RCA Preamp Output Harness DIN Sleeve Mounting Hardware Owner's Manual in English, French, Spanish and Portuguese 4-Channel Preamp Output Harness (Part No. 8634494218) l l l l Audio Speaker Impedance: Maximum Amp Power: RMS Power: Bass Control: Treble Control: Loud: Preamp Output: Cassette Signal-to-Noise Ratio: with Dolby B Noise Reduction: Tape Wow and Flutter: Tape Frequency Response: General Dimensions (w/o projecting parts/controls): Mass: Power Requirement (neg. grnd. ): Operating Temperature: Supplied Accessories: l l l Optional Accessories: Design and specifications subject to change without notice. 11 Location of Controls :VERSk " r) h10 I l-2 1. 4. i3 I;1 15 16 l-7 l-8 REL (Release) Button PWR (Power) Button Source (and Radio Band) Select Cassette Eject 5. [. . . ] If l unit already turned on, cassette insertion will override other audio source, such as radio. Cassette play will begin, and the display will indicate which tape program is in use, "1" or "2". The tape will continue to play until ejected, SRC button pressed, or unit turned off. l Ejecting The Tape Press the eject button completely towards the face of the unit. [. . . ]