User manual BLAUPUNKT TP DX-V NAV ITALIEN

[. . . ] 15 Positive connection . . . . . . . . . . . . . . . . . . . . . . . 15 Switching positive . . . . . . . . . . . . . . . . . . . . . . . . . 15 Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Negative (ground) connection . . . . . . . . [. . . ] 16 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 10 GENERAL INFORMATION Thank you for choosing a Blaupunkt product. We hope you enjoy using this new piece of equipment. Please read these operating instructions before using the equipment for the first time. The Blaupunkt editors are constantly working on making the operating instructions clearer and easier to understand. However, if you still have any questions on how to operate the device, please contact your dealer or the telephone hotline for your country. You will find the telephone number printed at the back of this booklet. We provide a manufacturer guarantee for our products bought within the European Union. You can view the guarantee conditions at www. blaupunkt. de or ask for them directly at: Blaupunkt GmbH Hotline Robert Bosch Str. 200 D-31139 Hildesheim DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH General information Installation and safety notices Before connecting your signal controller, please read the following information carefully. The battery's negative terminal must be disconnected for the entire time it takes to install and connect this device. When doing so, observe the vehicle manufacturer's safety notices (airbags, alarm systems, trip computers, immobilizers). < BOOSTER Setting the amplification for Audio 0 dB or 10 dB. OUT / 14 INSTALLATION Installation and safety notices Before connecting your signal controller, please read the following information carefully. The battery's negative terminal must be disconnected for the entire time it takes to install and connect this device. When doing so, observe the vehicle manufacturer's safety notices (airbags, alarm systems, trip computers, immobilizers). Before drilling any holes, make sure that no installed cables or vehicle components can be damaged. When installing the signal controller, select a location in the vehicle that allows you to attach it firmly into place using screws. The installation location should be such that the signal controller does not get in the way of the driver and cannot endanger the occupants in the event of the vehicle suddenly coming to a halt, for instance, during an emergency stop. The IR remote control should not be installed within the inflation range of airbags (driver, passenger side, side airbags) or in any position where it could be struck by the vehicle occupants' heads or knees. With regard to the installation location and the attachment using an adhesive pad, check and ensure that the holding strength of the installation surface is sufficient and suitable for all situations and safety requirements. DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Installation Note: Before connecting the monitors to your signal controller, check that the +/- and switching positive connections are working properly. Positive connection Connect the fuse holder (1A fuse) to protect the positive cable (permanent (1), see Fig. The fuse holder should be connected to the positive terminal at a distance of max. 30 cm from the vehicle battery (if necessary, drill a hole in the bulkhead and use the appropriate cable grommets). Switching positive Connect the switching positive cable (2) (see Fig. [. . . ] 30 cm from the vehicle battery (if necessary, drill a hole in the bulkhead and use the appropriate cable grommets). Switching positive Connect the switching positive cable (2) (see Fig. 1) to the switching positive ) of the main deoutput (ignition vice (e. g. If connecting to terminal 15 of the vehicle, protect the switching positive cable (2) by installing a fuse holder (1A fuse) at a maximum distance of 20 cm from the point of connection. Fuse If the fuse needs to be replaced, never bypass/bridge the fuse and never replace it with fuse types that are designed for higher currents. Negative (ground) connection Attach the negative cable (1) (earth/ GND, (3), see Fig. 1) directly to the vehicle body using a screw. [. . . ]