User manual BLAUPUNKT TP DX-V TITAN IBERIA

[. . . ] 12 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Telephone mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Guarantee/warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If necessary, switch these functions on or off in menu level 2. Scrolling On AM/AMT, you can also store six stations each. · Press TU, menu level 2 will appear in the display. SVENSKA Seek tuning Up Down << Down in short intervals (for FM only: "AF" must be switched off) >> Up in short intervals (for FM only: "AF" must be switched off) You can use the << >> buttons to tune into stations in your reception area. Important: a) You must have tuned into the station at least once before. To do this, you can press TS to start Travelstore in menu level 2. Storing stations On FM, you can store six stations on the preset buttons ST1 - ST6 for each of the memory banks I, II and T. NEDERLANDS ITALIANO Scrolling through the broadcasting networks (FM only) FRANÇAIS ENGLISH DEUTSCH Radio operation with RDS (Radio Data System) Radio operation with RDS (Radio Data System) · Press the desired preset button until the radio resumes play after the muting (takes approximately 2 seconds, confirmed by a beep). Note: Should you tune into a station which has already been stored before on another memory bank, the corresponding preset button and the memory bank will flash briefly in the display. has been completed, the radio will play the station with the strongest reception (ST 1). If desired, stations can also be stored manually on the Travelstore bank (see "Storing stations"). AM You can select the stations stored for the selected bank directly: · by pressing ST1 - ST6. To select a station on a different bank: · Press NEXT as often as necessary until the desired memory bank AM or AMT appears and then select the station by pressing ST1 - ST6. Recalling stored stations You can recall any stored station at the touch of a button. FM Recall the stations on the memory bank selected directly: · by pressing ST1 - ST6. This can be a great advantage when there are a large number of stations within your current reception range. Interference with strong adjacent stations can be reduced to an absolute minimum if you activate SHARX ON (factory setting). If necessary, refer to the section on "DSC programming ­ SHARX". 19 PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO Scanning stations with Radio Scan Changing the scan time The unit will automatically switch to mono if the signal received is not strong enough for stereo playback. If you would like to switch to mono, refer to "DSC programming - STEREO/MONO". FRANÇAIS To select a scanned station and switch off the Radio Scan function: · Press SCA or the rocker switch briefly. If you do not select a station, the scan function will automatically switch off after the frequency band has been run through completely. The unit will tune into the station you were listening to before you started the scan function. Switching from stereo to mono (FM) If reception is poor, you may get better sound quality by switching from stereo to mono in the DSC menu. Each time the radio is switched on, stereo playback is activated automatically. ENGLISH DEUTSCH Radio operation with RDS (Radio Data System) Radio operation with RDS (Radio Data System) PTY - Program Type PTY is an RDS service which an increasing number of broadcasting stations have begun to offer. This feature allows you to select FM stations according to their program type. After you have chosen the PTY of your preference, the corresponding stations can be selected either by seek tuning or using the scan function. Switching PTY on/off · Press PTY. When the function is active, the program type selected last will briefly appear in the display, e. g. [. . . ] If you remove the KeyCard during the reading process, "READ KC" will appear on the display panel. PEAK ON/OFF Switches the dynamic level display for the volume on/ off. READ KC UPDATE Use this function to delete CD names during CD and changer operation to make more storage capacity available for new discs. (See "Deleting CD names with DSC-UPDATE"). To quit the DSC programming mode and store the adjustment: · Press DSC. LED ON/OFF Here you can choose between LED ON or LED OFF. With LED ON, the "ON" knob will flash for extra antitheft protection when the unit has been switched off and the KeyCard removed. [. . . ]