User manual BLAUPUNKT TP DX-V TV SKANDINAVIEN

[. . . ] 24 6. 5" screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Monitor installation . . . . . . . . . . . . . . . . . . . . . . . . . 17 Prepare the working area . . . . . . . . . . . . . . [. . . ] 19 Insert the mounting frame in the headrest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Inserting the monitor . . . . . . . . . . . . . . . . . . . . . . 19 Check and adjust the monitor then apply the Velcro strips . . . . . . . . . . . . . . . . . . . 20 Example of a direct connection to a DVD player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Positive connection . . . . . . . . . . . . . . . . . . . . . . . 20 Negative (ground) connection . . . . . . . . 109 15 NOTES General information Thank you for choosing a Blaupunkt product. We hope you enjoy using this new piece of equipment. Please read these operating instructions before using the equipment for the first time. The Blaupunkt editors are constantly working on making the operating instructions clearer and easier to understand. However, if you still have any questions on how to operate the device, please contact your dealer or the telephone hotline for your country. Make the first cut inside the marked area at a point about 0. 5 cm from one of the corners, then make a diagonal cut to a point about 0. 5 cm from the opposite corner. Make a similar cut between the other two diagonally opposed corners. 18 FITTING DEUTSCH Lay the cable through the headrest Now pass the supplied cables through the opening so that they emerge from the underneath of the headrest. If possible, cover the cable with a cable tunnel. Now connect the power supply, ground and video signal cables, to check that the monitor is working. Inserting the monitor Before connecting the monitor, pass the connecting cables through the holes provided in the mounting plate, as shown in the illustration. Insert the monitor into the mounting plate, and attach it with appropriate fastenings. the connecting cables through the holes provided in the mounting plate, as shown in the illustration. Insert the mounting plate into the area that has been cut out, and fix it in place with appropriate fastenings. Monitor Mounting plate ESPAÑOL 19 DANSK PORTUGUÊS SVENSKA Insert the mounting frame in the headrest Before connecting the monitor, pass NEDERLANDS ITALIANO FRANÇAIS ENGLISH FITTING Check and adjust the monitor then apply the Velcro strips Connect the monitor, place it temporarily in the cut-out, and place the headrest into position. Check the various monitor settings such as brightness, headphone function, volume control and so on. Then attach the Velcro strips to the rear of the monitor, and push the frame onto the headrest. Take care not to press the screen itself, and apply pressure only in the region of the frame. Example of a direct connection to a DVD player Adapter cable for a direct connection to an AV source DVD - Player (IVDP-01) Audio L out Audio R out Video out Digital AV out in TP DX-V TV SKANDINAVIEN/6502 Positive connection Connect the fuse holder to protect the positive cable (+12 V). The fuse holder should be connected to the positive terminal at a distance of max. 30 cm from the vehicle battery (if necessary, drill a hole in the bulkhead and use the appropriate cable grommets). Masse /GND +12V 20 FITTING Negative (ground) connection Attach the negative cable (earth/GND) directly to the vehicle body using a screw. [. . . ] · If the installation requires holes to be drilled or any other changes to be made to the vehicle, please contact a specialist workshop in your area. REMOVAL To remove the screen, insert the extraction tool between the screen and the mounting plate. Insert the extraction tool at the place where a slot has been provided between the screen and the mounting plate. DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Removal Extraction tool 21 OSD MENU OSD menu Operation Press the "MENU" button on the display or on the remote control to open the OSD menu. Use the arrow buttons / to select the options and after you press the MENU button you can use the / to change the arrow buttons settings. Press the "EXIT" option to close the OSD menu again. TINT: To adjust the picture shade (only for NTSC) REVOLVE: To revolve the screen display - LEFT - RIGHT Horizontally mirrored - UP - DOWN Vertically mirrored RESET PICTURE: To reset the configured parameters to the factory default settings. [. . . ]