User manual BLAUPUNKT TP E FREESTYLER RB PL/CZ

[. . . ] Keys 1 - 6 Short press: TRAF button, to switch traffic information priority on/off Long press: RDS, to switch the RDS feature on/off Short press: BND button, to select the FM memory banks and LW/MW wavebands, and switch to radio mode Long press: TS, to start the Travelstore function = > ? : ; 26 TABLE OF CONTENTS Road safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Cassette play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Cassette playback begins. turn the volume control 3 to the right. To decrease the volume, turn the volume control 3 to the left. Setting the power-on volume You can set the unit's default power-on volume. Press the MENU button :. Keep pressing the or button 8 until "ON VOL" appears in the display. Set the power-on volume using the and buttons 8. To help you adjust the volume more easily, the volume will be increased / decreased as you make your changes. If you change the setting to "LAST VOL", the power-on volume will be the same as the volume level that was set before the unit was last switched off. Note: To protect your hearing, the maximum power-on volume that can be set for "LAST VOL" setting is "38". If the volume was higher before the unit was switched off and "LAST VOL" was selected, the volume will be set to "38" the next time the radio is switched on. 31 ADJUSTING THE VOLUME When you have finished making your changes, Configuring the confirmation beep For some functions you will hear a confirmation beep if you keep a button pressed for longer than two seconds. For instance, after storing a radio station to a station button you will hear a confirmation beep. You can configure the beep. press the MENU button : twice. Instantaneous volume reduction (mute) This feature allows you to instantaneously reduce (mute) the volume to a level preset by you. Briefly press button 2. "MUTE" appears in the display. Setting the mute level You can set the unit's mute volume level. Press the MENU button :. Note: Stations that were previously stored in this memory bank are deleted in the process. "T-STORE" appears in the display. After the process is completed, the station stored in FMT memory location 1 will be played. Stopping SCAN and continuing listening to a station Briefly press the MENU button :. Scanning is stopped and the station that was tuned into last will remain active. Setting the scantime Press the MENU button :. Keep pressing the or button 8 until "SCANTIME" appears in the display. Set the required scantime using the and buttons 8. When you have finished making your changes, press the MENU button : twice. Note: The set scantime also applies to scanning in CD changer mode. Listening to stored stations Select the memory bank or the waveband. Press the station button 1 - 6 = of the station you want to listen to. Programme type (PTY) Besides transmitting the station name, some FM stations also provide information on the type of programme that they are broadcasting. Your radio can receive and display this information. For example, the programme types can be: CULTURE TRAVEL JAZZ SPORT NEWS POP ROCK CLASSICS Using the PTY function, you can directly select stations of a particular programme type. Scanning receivable stations (SCAN) You can briefly play all the receivable stations. You can set the scanning time to between 5 and 30 seconds in the menu. Starting SCAN Hold down the MENU button : for longer than two seconds. "SCAN" briefly appears in the display followed by a flashing display of the current station name or frequency. 35 RADIO MODE PTY-EON If you specify the programme type and start seek tuning, the radio will switch from the current station to a station of the selected programme type. Note: If no station is found that corresponds to the selected programme type, you will hear a beep and "NO PTY" appears briefly in the display. [. . . ] "BASS" appears in the display. Keep pressing the Press the button 8 until "BAL" appears in the display. Adjusting the bass settings To adjust the bass, press the AUDIO button <. "BASS" appears in the display. Press the or button 8 to adjust the bass. When you have finished making your changes, or button 8 to adjust the balance (right/left). When you have finished making your changes, press the AUDIO button <. [. . . ]