User manual BLAUPUNKT TRAVEL PILOT RGS05

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BLAUPUNKT TRAVEL PILOT RGS05. We hope that this BLAUPUNKT TRAVEL PILOT RGS05 user guide will be useful to you.

Lastmanuals help download the user guide BLAUPUNKT TRAVEL PILOT RGS05.


BLAUPUNKT TRAVEL PILOT RGS05 : Download the complete user guide (819 Ko)

You may also download the following manuals related to this product:

   BLAUPUNKT TRAVEL PILOT RGS05 annexe 1 (848 ko)

Manual abstract: user guide BLAUPUNKT TRAVEL PILOT RGS05

Detailed instructions for use are in the User's Guide.

[. . . ] Fitting instructions TravelPilot RGS 05 8 622 400 046 7 612 001 120 GB Safety instructions Installation and connection regulations While installing and mounting this equipment, you must disconnect the negative terminal of the battery. Important: You must also comply with all safety instructions given by the auto manufacturer (alarm system, vehicle immobilizer, airbag)!Before drilling holes for mounting the equipment or laying the wiring, make sure that no existing wiring or auto parts (such as the petrol tank, fuel line) will be damaged. In order to avoid any interference, lay all wiring far enough away from the wire harnesses. [. . . ] On estate wagons and liftback cars, set the antenna on the roof with its magnetic foot, Fig. For estate wagons and liftback cars, lay the antenna wire along the rain gutter downwards and into the interior of the vehicle, Fig. Any obstacles near the antenna, such as roof or bicycle carriers, may adversely affect or even prevent satellite reception. Lay the antenna wire into the interior of the vehicle and connect the BNC plug on the antenna wire with the antenna jack on the GPS receiver. It is advisable to remove the antenna from the roof when driving through a carwash. Installation of the GPS receiver The mounting location of the GPS receiver depends on the length of the antenna cable (2. 5 m) and the connection line to the navigation unit (1. 5 m). Do not use screws longer than 7 mm, otherwise you may destroy the GPS receiver, Fig. 10. Loudspeaker Install the loudspeaker for the voice directions in the foot area of the vehicle so that it is possible to understand the voice instructions clearly. Connecting the sensors for the navigation unit Lay the connecting wires for the precision resistor, the wheel sensors, the loudspeaker and the magnetic field sensor to the navigation unit and connect them to the compact plugs, Fig. If it is not possible to mount the display on a swivel base, you may alternately use a gooseneck. You can order the gooseneck as an accessory under the order number 7 607 039 100. The hook-up wire can be laid into the base either from the side or from underneath. In order to lay the wire into the base from underneath, drill a 15 mm hole where the display is to be installed and pull the plug from the display. In order to pull the plug in the display, screw it apart as follows: 1. Loosen the four screws on the back of the display and remove the rear plate (Fig. Push the wire through the hole where the display is to be installed, push it from underneath into the base and plug it in. Loosen the four screws on the back plate of the display and remove the rear plate (Fig. Remove the cover from the back plate of the display and remove the retaining spring (Fig. Pull the base off the back plate and insert it where the cover was located (Fig. Push the retaining spring into the notch in the base, insert the cover where the base was located, lay the wire through the base and reassemble the display (Fig. In order to mount the base, unscrew it and use four screws to fix it to the installation location (Fig 18). Modifications reserved! GPS receiver Mounting the antenna Important information: - Mount the antenna on a metal roof only. It is not permissible to mount the antenna on synthetic roofs or aluminium. Special case: T = 90°, do not mount the metal holder facing in the direction of the magnetic strip. Special case ° 90 - 26 - Z 8 mm metal holder will affect the magnetic field Set angle: The edges of the wheel sensor must be set at a distance conforming to Z. Fig. [. . . ] Test passed? yes no Check the mechanical wiring to the precision resistor. (Chassis and rear window wiring, signal wire to the basic navigation unit) O. K. ? Replace the basic navigation unit and do a complete calibration. yes Test the signal wire to the basic unit with an ohmmeter on transition. (Resistance measures 3. 3 m) no Repair wiring. no Replace precision resistor and do a complete calibration on the basic navigation unit. - 32 - Error: Regular locating loss even after a short drive Load the installation disk. Select , , find compass location", then select , , compass ellipse". [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLAUPUNKT TRAVEL PILOT RGS05

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BLAUPUNKT TRAVEL PILOT RGS05 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag