User manual BLAUPUNKT TSA 460

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BLAUPUNKT TSA 460. We hope that this BLAUPUNKT TSA 460 user guide will be useful to you.

Lastmanuals help download the user guide BLAUPUNKT TSA 460.


Mode d'emploi BLAUPUNKT TSA 460
Download

You may also download the following manuals related to this product:

   BLAUPUNKT TSA 460 annexe 1 (493 ko)

Manual abstract: user guide BLAUPUNKT TSA 460

Detailed instructions for use are in the User's Guide.

[. . . ] We provide a manufacturer guarantee for our products bought within the European Union. You can view the guarantee conditions at www. De or ask for them directly at: Blaupunkt GmbH Hotline Robert-Bosch-Str. Installation and connection instructions The battery's negative terminal must be disconnected for the entire time it takes to install and connect the device. [. . . ] Class D 4/3/2 Channel Amplifier TSA 460 The amplifier is suitable for connection to car radios that are equipped with RCA connections. If you want to connect it to car radios that are equipped with an ISO connection, please use the Blaupunkt ISO-RCA adapter. Power 2 ohms RMS power 4 ohms RMS power 2 ohms Frequency response Signal-to-noise ratio Input sensitivity Stability Low pass filter (Low Pass) High pass filter (High Pass) Subsonic filter Dimensions WxHxD (mm) Inner housing Outer housing Positive/negative connection The cross section of the positive and negative cables must be at least 6 mm2. Use cable grommets to protect cables against sharp-edged holes. Securely screw a standard 6 mm2 negative cable to an interference-free earth connection point (bolt connected to the car body, car body sheet metal) ­ though do not connect it to the negative terminal of the battery. Scratch the surface down to the bare metal at the point at which the earth contact is made and apply graphite grease. Connection examples Before you can connect the cables to the amplifier, you must first detach the top half of the housing shell (see "Removing the outer housing"). Please use high-quality Blaupunkt RCA cables for this connection. LP / HP / FULL switch Before installing, adjust the X-OVER switch on the power amplifier to set the low pass filter (LP), high pass filter (HP) or full-range setting (FULL). if you select the FULL position , the full frequency response will be used. Using the integrated crossovers is particularly useful in the case of multi-channel sound systems with a separate subwoofer. In order to obtain the best sound when a subwoofer is connected, the subwoofer must be separated as far as the frequencies it receives are concerned, i. It must only be fed with low frequencies (bass). To ensure that this is the case, select LP and use the crossover frequency control to adjust the upper frequency to between 50 Hz and 250 Hz. This ensures that every subwoofer is optimally separated as far as the frequencies it receives are concerned. If HP is selected, you can use the associated crossover frequency control to adjust the lower cut-off frequency to between 50 Hz and 250 Hz. If you want to precisely optimise the acoustic settings of the crossover, we recommend you obtain advice from a Blaupunkt dealer. It is very important that you take into account the specifications of the loudspeakers being used whilst you are adjusting the crossover. The switching line must be connected when connection is carried out using the RCA jacks or the loudspeaker jacks of the car radio. Tri mode You can operate 2 loudspeakers and at the same time switch on a third loudspeaker in mono mode (bridge mode) (see Fig. GAIN control You can use the GAIN control to adjust the input sensitivity of the Blaupunkt power amplifier to the output voltage of your car radio's preamp output. When connecting a car radio produced by another manufacturer, you must adjust the input sensitivity in accordance with the information provided by the manufacturer. [. . . ] If you want to precisely optimise the acoustic settings of the crossover, we recommend you obtain advice from a Blaupunkt dealer. It is very important that you take into account the specifications of the loudspeakers being used whilst you are adjusting the crossover. sUB SONIC The subsonic filter is used when a subwoofer is connected to the amplifier. It can be activated in order to protect the subwoofer against mechanical overload by low frequencies that are outside our hearing range. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLAUPUNKT TSA 460

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BLAUPUNKT TSA 460 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag