User manual BLAUPUNKT VA 4100

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BLAUPUNKT VA 4100. We hope that this BLAUPUNKT VA 4100 user guide will be useful to you.

Lastmanuals help download the user guide BLAUPUNKT VA 4100.


BLAUPUNKT VA 4100 : Download the complete user guide (449 Ko)

Manual abstract: user guide BLAUPUNKT VA 4100

Detailed instructions for use are in the User's Guide.

[. . . ] 200 D-31139 Hildesheim For additional information on the Blaupunkt product line visit our web site at: http://www. The battery's negative terminal must be disconnected for the entire time it takes to install and connect the device. You must observe the vehicle manufacturer's safety notices (airbags, alarm systems, trip computers, immobilizers) regarding this. As regards safety in the event of an accident, the Blaupunkt power amplifier must be professionally secured in position. [. . . ] This ensures that every subwoofer is optimally separated as far as the frequencies it receives are concerned. If HP is selected, you can use the associated XOVER frequency control to adjust the lower cut-off frequency to between 50 Hz and 250 Hz. If you want to precisely optimise the acoustic settings of the XOVER, we recommend you obtain advice from a Velocity dealer. It is very important that you take into account the specifications of the loudspeakers being used whilst you are adjusting the XOVER. Power 2 ohms RMS power 4 ohms RMS power 2 ohms Frequency response Signal-to-noise ratio Input impedance Damping factor Input sensitivity Stability Low pass filter (Low Pass) High pass filter (High Pass) Subsonic filter Remote control for bass GAIN Dimensions WxHxD (mm) If the XOVER is activated (LP or HP) by adjusting the position of the XOVER switch, you can then use the corresponding control to adjust the XOVER frequency of the respective filter to anywhere between 50 Hz and 250 Hz or 50 Hz and 250 Hz (i. In order to obtain the best sound when a subwoofer is connected, the subwoofer must be separated as far as the frequencies it receives are concerned, i. Firstly, turn down the GAIN control on the amplifier to minimum and set the LOW PASS frequency control to its centre position. Now play some music on your car sound system that you are very familiar with and that contains some low bass (e. Now slowly increase the volume of the subwoofer by turning the GAIN control on the amplifier in a clockwise direction until you feel that the sound of the music is well balanced, i. Now listen to the relationship between deep male voices and the upper bass and also take note of the relationship between the upper bass (kick bass) and the lower bass. The bass should ideally sound crisp and have a clear low bass component, and male voices should neither sound too weak nor should they billow out. If male voices seem to billow out or the low bass is too weak, you should turn the LOW PASS frequency control slightly towards minimum and then continue making your adjustments as described in point 2 onwards. If the bass sounds low but dirty and booming or the male voices sound too weak, you should turn the LOW PASS frequency control slightly towards maximum. Next, continue making your adjustments as described in point 2 onwards. If you want to precisely optimise the acoustic settings of the XOVER, we recommend you obtain advice from a Blaupunkt dealer. It is very important that you take into account the specifications of the loudspeakers being used whilst you are adjusting the XOVER. The cross section of the positive and negative cables must be at least 12 mm2. Securely screw a standard 12 mm2 negative cable to an interference-free earth connection point (bolt connected to the car body, car body sheet metal) - though do not connect it to the negative terminal of the battery. Scratch the surface down to the bare metal at the point at which the earth contact is made and apply graphite grease. 5 The switching line must be connected when connection is carried out using the RCA jacks or the loudspeaker jacks of the car radio. [. . . ] If amplifier performance temporarily declines, then you know that you are running your system at its limits, but can nevertheless rest secure in the knowledge that it will not abandon you by cutting out entirely. Using the connecting rails, you can install several amplifiers next to one another to form a cool multichannel monster system with a convincing look. An additional advantage of the connecting rails and side pieces is plenty of storage space for avoiding messy bunches of cables. Our products are made from materials that can be disposed of in an environmentally sensitive manner and are suitable for appropriate recycling. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLAUPUNKT VA 4100

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BLAUPUNKT VA 4100 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag