User manual BLUEANT Q2

[. . . ] SMART BLUETOOTH HEADSET User Guide Contents Introduction Charge Your Q2 Switching the Q2 On and Off Pair the Q2 with your Phone Transfer your Phonebook Wearing Your Q2 Changing the Ear Bud Stabilizing Ear Buds Use Your Voice to Control the Q2 Use Your Voice to Make Phone Calls Use Your Voice to Answer Calls List of Voice Commands Transferring your Phonebook Contacts to the Q2 6 7 7 8 8 10 10 10 11 12 12 13 15 ENGLISH 3 Automatically Transferring your Phonebook Contacts to the Q2 Manually Transferring your Phonebook Contacts to the Q2 Updating your Phonebook Contacts on the Q2 Listening to Audio Reconnecting to the Q2 Using 2 Phones with the Q2 (Multipoint) Which Phone is Used for Calls? Multiple Calls (Call Waiting)* Firmware Upgrades Function Reference Phone Specific Tips and Tricks Android Apple® iPhone® BlackBerry 15 15 16 17 17 18 18 19 20 20 23 23 23 24 4 Other Models Troubleshooting Resetting the Q2 Specifications Help and Support Terms and Conditions 24 25 30 31 31 32 ENGLISH 5 Introduction Welcome to the BlueAnt Q2: the voice controlled smart Bluetooth headset for smartphone users. With the Q2 you can make outgoing calls and answer incoming calls using just your voice, and you will always know who is calling without looking at your phone because the Q2 will read out the caller's name or number. Multi-Function Button (MFB) Microphones Vol Indicator Light Vol + 6 Charge Your Q2 Your Q2 has been given an initial partial charge to get you started, but for best results we recommend you fully charge it using the supplied USB cable and adaptor. > You should charge the Q2 whenever it announces that the battery is Very Low. [. . . ] If your phone supports the A2DP profile then simply start playing music or any other audio (including turn-by-turn directions from a GPS application on your phone) and it will automatically transfer to the Q2. You can use your voice to answer or ignore the call. Or: > Click the MFB to accept the call. > Double click the MFB to ignore the call. The audio will resume when the call ends. If you want to exit A2DP streaming mode to do something else, click the MFB. If you do not say a command within a few seconds the music will resume playing. Reconnecting to the Q2 If you take your phone out of range of the Q2 for more than 2 minutes, the Q2 will go into "sleep mode" to save battery. When you bring your phone back into range, simply click the MFB to reconnect. ENGLISH 17 Alternatively, use the hardware switch to turn the Q2 off whenever you are not using it. The Q2 will automatically reconnect to your phone if the phone is in range when you switch the Q2 on. Depending on your phone, this may take a few seconds. Please ensure that Bluetooth is enabled on your phone. Using 2 Phones with the Q2 (Multipoint) Up to 2 devices can connect to the Q2 at the same time. If either phone rings, you can answer it with the Q2. Use the Pair Me command to put your Q2 back into pairing mode to pair another phone. Any currently connected phone will be disconnected during pairing, so you will need to reconnect afterwards. Which Phone is Used for Calls? When you have two phones connected to the Q2 at the same time you can always answer an incoming call on either phone. If you initiate a call through the Q2 (for example by saying Phone Commands) then the call takes place on the primary phone: the one that connected to the Q2 first. 18 Note: Only the primary phone can play music through the Q2 via A2DP. Multiple Calls (Call Waiting)* If you receive an incoming call while you are already on a call the Q2 will play a tone to alert you. > Hold Vol + for about 1 second to put your current call on hold and answer the incoming call. > Hold Vol - for about 1 second to end the current call and answer the incoming call. > Once you have a call on hold, you can switch between calls by holding Vol + for about 1 second. Note: If one of the calls ends, some phones do not automatically resume the held call. If this happens, hold Vol + for about 1 second to release the hold and resume the other call. Tip: If you are using multipoint, both phones remain connected during calls so you can also use these controls to switch between calls on both phones. * To use this feature, your phone and network must support call waiting. ENGLISH 19 Firmware Upgrades To enhance your experience, we are continually upgrading the Q2 firmware. [. . . ] This setting determines how precisely the words that you say need to match the speech patterns that the Q2 has been configured to recognize. You can change it by using the Sensitivity Level command. up when you turn the Q2 on and off, but not at other times. Resetting the Q2 If you are having problems with the Q2, you can reset it and start again. Resetting the Q2 will clear all the stored pairing settings on the Q2, delete any stored contact details and put the device back into pairing mode. Delete any existing pairing information from your phone and turn the phone off and back on again to clear the phone memory. [. . . ]