User manual BLUESTORK BS-WG RT4MD

[. . . ] Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All product, company, brand names are trademarks or registered trademarks of their respective companies. They are used for identification purpose only. Specifications are subject to be changed without prior notice. 4 Ports 11g Wireless ADSL2/2+ Router i FCC Radiation Norm This equipment has been tested and found to comply with limits for a Class B digital device pursuant to 47 CFR, Part 2 and Part 15 of the Federal Communication Commission (FCC) rules. Operation is subject to the following two conditions: 1. [. . . ] Translated ToS: The Type of Service field takes values from 1 to 255. The selections are 0, 1, 2, 3, 4, 5, 6, 7. 4 Ports 11g Wireless ADSL2/2+ Router 119 4. 4. 17. 4 WLAN Egress Support WLAN Egress is supported; however, it is hard-coded and is not configurable on the Egress pages. More information is available in the WLAN QoS Support section. 4 Ports 11g Wireless ADSL2/2+ Router 120 4. 4. 18 Advanced ­ Shaper The Shaper Configuration page (Figure below) is accessed by selecting Shaper on the Advanced main page. The shaper algorithms only support: HTB Queue Discipline Note: Egress TCA is required if shaper is configured for that interface. Interface: The selections are WAN/LAN interfaces except WLAN, which does not support Shaper feature. This field needs to be selected before shaper configuration. HTB Queue Discipline: The hierachical token bucket queue discipline is a rate-based shaping algorithm. This algorithm rate shapes the traffic of a class over a specific interface. All CoSx traffic is assigned a specific rate to which data will be shaped to. For example: If CoS1 is configured to 100Kbps then even if 300Kbps of CoS1 data is being transmitted to the interface only 100Kbps will be sent out. Max Rate: This field is applicable for the HTB Queue Discipline and Low Latency Queue Discipline, both are rate-based shaping algorithms. An example of the configuration is given as follows. 4 Ports 11g Wireless ADSL2/2+ Router 121 4. 4. 18. 1 HTB Queue Discipline Enabled In the example below, HTB Queue Discipline is enabled. The Hinet connection has a total of 300 Kits of bandwidth, of which 100 Kits is given to CoS1 and another 100 Kits is given to CoS2. When there is no CoS1 or CoS2 packets, CoS6 packets have the whole 300 Kbits of bandwidth. 4 Ports 11g Wireless ADSL2/2+ Router 122 4. 4. 19 Advanced ­ SSH Access Control The SSH Access Control page (Figure below) allows you to access the 4 Ports 11g Wireless ADSL2/2+ Router remotely via SSH from the WAN side. The configuration of a WAN IP address for SSH access control is very similar to the configuration of a WAN IP address for Web access control. Refer to Web Access Control Page for field descriptions and configuration procedures. 4 Ports 11g Wireless ADSL2/2+ Router 123 4. 5 Advanced ­ LAN The LAN Configuration page allow you to select or assign physical interfaces to LAN group and configure LAN IP Address and DHCP functionality. Meanwhile, Click LAN Configuration and the following screen will be shown. 4 Ports 11g Wireless ADSL2/2+ Router 124 4. 5. 1 Advanced ­ LAN ­ LAN Configuration Click LAN Configuration and the following screen will be shown. Click Add or Remove Interfaces from list under the different LAN Group. The LAN Group features only supported under Bridge Mode setting. Interfaces under the same LAN Group (WLAN, Ethernet, USB (Optional) and SSID) will have the ability to communicate with each other. Different LAN Group are prohibited to communicate with one another. Click Configure for detail LAN Group setting. Refer to next section for detail LAN Configuration or Setting. Apply: Click Apply to complete the setting. Cancel: Click Cancel to ignore all the changes. [. . . ] Subnet Mask: Short for SubNetwork Mask, subnet mask is a technique used by the IP protocol to filter messages into a particular network segment, called a subnet. The subnet mask consists of a binary pattern that is stored in the client computer, server, or router. This pattern is compared with the incoming IP address to determine whether to accept or reject the packet. TCP: Transfer Control Protocol: Works together with Internet Protocol for sending data between computers over the Internet. [. . . ]