User manual BLUMAX GPS-4013

[. . . ] If you do not follow these rules, the battery inside Blumax Bluetooth GPS-4013 Receiver may become heat, explode or burn itself, and this will lead to very serious damage The Lithium battery inside the Blumax Bluetooth GPS-4013 Receiver should be recycled. ⷠWhile in the hospital, turning off the Blumax Bluetooth GPS-4013 Receiver is recommended. Like other common equipments do, wireless GPS receiver may also affect these medical equipments which use radio frequency and make these equipments malfunction · For a long period not using Blumax Bluetooth GPS-4013 Receiver, take out the battery and store it in dry/cool places. [. . . ] Take the power cable and connect it to the power jack (mini USB type) and charge through car cigarette adaptor This will begin to charge the battery Charging time is 3 hours typically The LED that represents the battery is the right-most battery icon (shown in below) *Unit package contents may vary depending on countries without prior notice If the LED is red, that means battery power is critically low. please charge · If the LED is green, that means battery is charging now. ⷠWhen the Power LED is off, the battery is fully charged. When you plug into the mini USB cable to charge your unit, it will take 5~10 seconds then you can see the green LED turning on Fully charge the battery when using at the first time A fully charged battery can last up to 32 hours continuously operation 2. Activate the Bluetooth function in your PDA/Smart phone or PC Before activating the Bluetooth function in your PDA/PC, please switch on Blumax Bluetooth GPS-4013 Receiver for paring and check if your device is equipped with Bluetooth function If not, you may need to acquire an optional CF/SD on off Bluetooth card or Bluetooth dongle NOTE: The pairing procedure is required to execute in the first time only. Automatically create a shortcut in Bluetooth Manager window After the pairing complete, the system will then find a quick connect device "BT A+ GPS" in Bluetooth Manager. In further use, you just need to click it to connect to this Bluetooth GPS Receiver. Check the Serial Port in Bluetooth Setting After complete pairing with the Receiver, please click "Serial Port" to confirm the assigned COM port. If you use PDA/ PC to pair the GPS Receiver, please check "Outbound COM port". Set correct Serial Port in your map software Activate your navigation software and make sure to select the correct "Serial Port". NOTE: In the map software such as TomTom, you might need to change preference and set "Other Bluetooth GPS" according to PDA/phone model. In some case please consult map software company to vary the setting if you have issue on positioning 6. Switch off the Bluetooth function Switch off GPS function in your PDA/Smart phone/PC, then the Bluetooth connection will be disconnected automatically. Then put Blumax Bluetooth GPS-4013 Receiver power switch to "OFF" position. Function of Smart Power Control (Power saving mode) Blumax Bluetooth GPS-4013 Receiver supports Smart Power control (Power saving mode) It can automatically enter sleeping mode after the Bluetooth connectivity is turned off, so the Blue LED will turn to flash every 5 seconds. Thus you can always power it on with very low power consumption Under power saving mode, when detecting Bluetooth is being connected, Blumax Bluetooth GPS-4013 Receiver will wake up itself and the blue LED will turn to flash every 2 second and GPS Orange LED will be also on Bluetooth on, but not Always on: connected to any Bluetooth devices yet Bluetooth Status LED Blue Slowly blinking: Quickly blinking: Red Green Green Blinking: Light On: Light Off: Always on: Orange Quickly Blinking: Sleeping mode (1 time / 5 seconds) Bluetooth is connected and ready for data transmission (1 time / 2 seconds) The battery is too low The battery is charging The battery is fully charged Acquiring satellites, GPS position not fix GPS position is fixed, Navigation Before you use GpsView software, you need to install Blumax Bluetooth GPS-4013 Receiver driver. [. . . ] Thank you for your purchase of GPS product from the company The company warrants this product to be free from defects in materials and workmanship for one year from the date of purchase The warranty for accessories is six months The stamp of distributor or a copy of the original sales receipt is required as the proof of purchase for warranty repairs. The company will, as its sole option, repair or replace any components, which fail in normal use. Such repair or replacement will be made at no charge to the customer for parts or labor. [. . . ]