User manual BOSCH KAD 62V40AU/03 SHORT INSTRUCTIONS

[. . . ] All other charges, including transportation charges for replacements under this warranty and labor costs not specifically covered by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product. The Registration Card included with the product should be promptly completed by you and mailed back to U-Line. The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God, such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation, unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the controls; door reversal; or cleaning the condenser. [. . . ] If the ice maker is not level, adjust the feet on the corners of the unit as necessary (see Figure 11). 13 User's Manual CHECK LEVEL UL314 Figure 10 TURN FOOT TO ADJUST UL205A Figure 11 3. Check the levelness after each adjustment and repeat the previous steps until the unit is level. REVERSING THE DOOR All U-Line units (except Stainless Steel models) may be left or right hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side (see Figure 12). To reverse the door: UL318B Figure 12 14 1. Remove top hinge screw pin (7/64" Allen wrench) from 3. Remove door by tilting forward and lifting off bottom hinge pin. Remove top hinge (3 screws), reinstall hinge screw pin, and remount on opposite side BOTTOM (see Figure 15). HINGE SCREW PIN UL313 Figure 15 UL310 Figure 13 2. Remove plastic screw plugs (3 each, top and bottom) from new hinge location. Do not discard (see Figure 14). 4. Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see Figure 16). SCREW PLUGS DOOR CLOSER INSERTS UL308 UL312 Figure 14 Figure 16 15 User's Manual 5. Remove existing bottom hinge (3 screws) and remount on opposite side TOP Remove hinge screw pin. With bottom of door facing up, remove pivot plate (2 screws), flip over, and remount on opposite side of door (see Figure 17). UL319 Figure 17 7. Holding door upright with top of door tilted forward, place hole of door pivot plate on bottom hinge screw pin (see Figure 18). When built-in, your U-Line product does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed. !CAUTION Do not install unit behind closed doors. Table 3. Built-in Cabinet Dimensions Model CLR2060 Width 14-15/16" Unit Dimensions Height 34-1/8" Depth 24" NOTE To ease unit installation and removal, increase the above measurements. It is recommended that the cabinet rough opening dimensions be increased by at least 1/4" over the dimensions given for your unit. The unit must be located to allow clearance for water, drain and electrical connections in the rear of the ice maker. W H D UL118 Figure 23 19 User's Manual INITIAL START-UP Once installation and leveling is complete, the unit is ready for initial start-up and operation. Your unit is shipped in the OFF position, however, you may turn it ON/OFF using the cycle selector switch located in the grille (see Figure 24). CYCLE SELECTOR SWITCH UL316B Figure 24 1. Plug the appliance cord into a 115V polarized and grounded electrical outlet. Open the water supply valve in the main water source. Put the cycle selector switch in the ICE position (press the switch to the right). The water fill valve will energize and fill the water reservoir. [. . . ] The problem could be something very simple which can be solved without a service call. TROUBLESHOOTING GUIDE !DANGER ! ELECTROCUTION HAZARD NEVER attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected. Troubleshooting -- What to check when problems occur Problem The unit does not operate. Possible Cause No electrical power to the unit. Remedy Make sure power cord is plugged in. [. . . ]