User manual BOSCH KAD 62V40AU/05 SHORT INSTRUCTIONS
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BOSCH KAD 62V40AU/05. We hope that this BOSCH KAD 62V40AU/05 user guide will be useful to you.
Lastmanuals help download the user guide BOSCH KAD 62V40AU/05.
You may also download the following manuals related to this product:
BOSCH KAD 62V40AU/05 SUPPLEMENT (887 ko)
BOSCH KAD 62V40AU/05 INSTALLATION INSTRUCTIONS (1245 ko)
Manual abstract: user guide BOSCH KAD 62V40AU/05SHORT INSTRUCTIONS
Detailed instructions for use are in the User's Guide.
[. . . ] All other charges, including transportation charges for replacements under this warranty and labor costs not specifically covered by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product. The Registration Card included with the product should be promptly completed by you and mailed back to U-Line or you can register on-line at www. U-LineService. com. The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God, such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation, unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the controls; door reversal; or cleaning the condenser. [. . . ] Allow stain/finish to dry thoroughly (at least 24 hours per coat) in accordance with the stain/finish manufacturer's instructions prior to re-installing the wood trim inside the cabinet of the 75 BEV. Failure to do so may cause the inner liner of the unit to have a permanent odor, which is not covered by the warranty. (1) You can leave as is, (2) add a final finish coat or (3) you may stain the wood trim. The final finish coat was not applied at the factory so that the wood trim could be stained. Review the following guidelines when staining and or sealing the wood to ensure proper adhesion and durability of the finish. Remove screws securing wood trim to the two racks attached at the drawer slides so wood can be removed for treatment. Lightly scruff sand the wood trim with 280 grit 3MTM Tri-M-IteTM sandpaper. Apply a thin coat of a clear protective finish; the factory-applied seal is compatible with virtually all finishes. A low odor, water clean up, quick drying finish such as Minwax® Polycrylic® Protective Finish is recommended. 5.
To stain for a different wood color: 1. Remove screws securing wood trim to the two racks attached at the drawer slides so wood can be removed for treatment. Replace three plastic plugs removed in step 8 into holes on top of unit. Reinstall grille (one screw).
On Combo Model 75A (built-in installations only), changing the door mounting to the left side may interfere with ice bucket removal. To reverse the door mounting on Models Combo 75A and 75R (except Stainless Steel models) perform the following: 1. Remove four plastic plugs in hinge holes, top of cabinet, opposite side (Figure 29). Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge (Figure 28). Remove bottom hinge from cabinet (four screws) and screws on opposite side of cabinet (Figure 31). Remove pivot screw from bottom hinge, invert screw and reinstall pivot screw in hinge (Figure 28). Install bottom hinge on cabicabinet, opposite side, aligning flat edge of hinge with outer edge of unit. Relocate plastic spacer/ bushing on bottom of door to opposite side (Figure 27). Align flat edge of top hinge with outer edge of unit and fasten upper hinge to unit (four screws). Replace four plastic plugs removed in step 5 into holes on top of unit. [. . . ] Manual defrost models should be defrosted approximately every eight weeks. However, this interval may not be adequate in periods of high humidity or heavy usage. Defrost your unit whenever the frost thickness is 1/4" or greater. To defrost, turn the unit OFF, remove cubes and prop door open at least two inches.
Frost free units will NEVER need defrosting. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSCH KAD 62V40AU/05
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSCH KAD 62V40AU/05 will begin.